Safety Standard Certified Ceramic Capacitors/High Voltage ... - Murata

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.C85E.pdfApr.7,2014Type KJ Specifications and Test MethodsContinued from the preceding page.No.ItemSpecificationsTest Method19HighTemperatureExposure(Storage)CapacitanceChangeD.F.I.R.Within ±20%Char.B, E1000MΩ min.SpecificationsD.F.V5.0%Set the capacitor for 1000±12 hrs. at 150±3°C.Pre-treatment:Capacitor should be stored at 125±3°C for 1 hr., then placedat room condition* for 24±2 hrs.Post-treatment:Capacitor should be stored for 24±2 hrs. at room condition.*20 ThermalShockAppearanceCapacitanceChangeD.F.I.R.No marked defect except color change of outercoating.Char.BEChar.B, E3000MΩ min.Capacitance ChangeWithin ±10%Within ±20%SpecificationsD.F.V5.0%The capacitor should be subjected to 300 cycles.Step12Temperature (ºC)-55+0/-3125+3/-0Time (min)3030Pre-treatment:Capacitor should be stored at 125±3°C for 1 hr., then placedat room condition* for 24±2 hrs.Post-treatment:Capacitor should be stored for 24±2 hrs. at room condition.*21Resistance toSolventsAppearanceCapacitanceChangeD.F.I.R.No marked defectChar.BEChar.B, E3000MΩ min.Capacitance ChangeWithin ±10%Within ±20%SpecificationsD.F.V5.0%Per MIL-STD-202 Method 215Solvent 1: 1 part (by volume) of isopropyl alcohol3 parts (by volume) of mineral spiritsSolvent 2: Terpene defluxerSolvent 3: 42 parts (by volume) of water1 part (by volume) of propylene glycolmonomethyl ether1 part (by volume) of monoethanolomine22 BiasedHumidityAppearanceCapacitanceChangeD.F.I.R.No marked defectChar.BEChar.B, E3000MΩ min.Capacitance ChangeWithin ±10%Within ±15%SpecificationsD.F.V5.0%Apply the rated voltage and DC1.3+0.2/-0V (add 6.8kΩ resistor)at 85±3°C and 80 to 85% humidity for 1000±12 hrs.Pre-treatment:Capacitor should be stored at 125±3°C for 1hr., then placedat room condition* for 24±2 hrs.Post-treatment:Capacitor should be stored for 24±2 hrs. at room condition.*1223 MoistureResistanceAppearanceCapacitanceChangeD.F.I.R.No marked defectChar.BEChar.B, E3000MΩ min.Capacitance ChangeWithin ±10%Within ±20%SpecificationsD.F.V5.0%Apply 24 hrs. of heat (25 to 65°C) and humidity (80 to 98%)treatment shown below, 10 consecutive times.Pre-treatment:Capacitor should be stored at 125±3°C for 1 hr., then placedat room condition* for 24±2 hrs.Post-treatment:Capacitor should be stored for 24±2 hrs. at room condition.*°C7065605550454035302520151050-5-10TemperatureHumidity90-98%Humidity Humidity Humidity80-98% 90-98% 80-98%+10-2 °CInitial measurementOne cycle 24 hoursHumidity90-98%0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24Hours* "Room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa74