Safety Standard Certified Ceramic Capacitors/High Voltage ... - Murata

More documents

Recommendations

Info

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.C85E.pdfApr.7,2014CH CharacteristicsPart NumberRated<strong>Voltage</strong>CapacitanceBodyDia. DLeadSpacing F(mm)BodyThickness TLeadPackageLong BulkLeadPackageShort BulkDEF2CLH020Cppp 6300Vdc(p-p) 2.0pF±0.25pF 7.0mm max. 7.5 6.0mm max. A3B J3B N3ADEF2CLH030Cppp 6300Vdc(p-p) 3.0pF±0.25pF 7.0mm max. 7.5 6.0mm max. A3B J3B N3ADEF2CLH040Cppp 6300Vdc(p-p) 4.0pF±0.25pF 7.0mm max. 7.5 6.0mm max. A3B J3B N3ADEF2CLH050Dppp 6300Vdc(p-p) 5.0pF±0.5pF 7.0mm max. 7.5 6.0mm max. A3B J3B N3ADEF2CLH060Dppp 6300Vdc(p-p) 6.0pF±0.5pF 7.0mm max. 7.5 6.0mm max. A3B J3B N3ADEF2CLH070Dppp 6300Vdc(p-p) 7.0pF±0.5pF 8.0mm max. 7.5 6.0mm max. A3B J3B N3ADEF2CLH080Dppp 6300Vdc(p-p) 8.0pF±0.5pF 8.0mm max. 7.5 6.0mm max. A3B J3B N3ADEF2CLH090Dppp 6300Vdc(p-p) 9.0pF±0.5pF 8.0mm max. 7.5 6.0mm max. A3B J3B N3ADEF2CLH100Jppp 6300Vdc(p-p) 10pF±5% 8.0mm max. 7.5 6.0mm max. A3B J3B N3AThree blank columns are fi lled with the lead and packaging codes. Please refer to the three columns on the right for the appropriate code.LeadPackageTaping1156
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.C85E.pdfApr.7,2014DEF Series Specifications and Test MethodsNo.ItemSpecificationsTest Method1 Operating Temperature Range -25 to +105°C2 Appearance and Dimensions457 QDielectricStrengthInsulationResistance (I.R.)Between LeadWiresBody InsulationBetween LeadWires8 Temperature CharacteristicsNo visible defect, and dimensions arewithin specified range.3 Marking To be easily legibleNo failureNo failure10000MΩ min.6 Capacitance Within specified tolerance400+20C* 2 min. (30pF under)1000 min. (30pF min.)Char. CH: 0±60ppm/°CChar. SL: +350 to -1000ppm/°C(Temp. range: +20 to +85°C)StepTemp. (°C)120±2The capacitor should be visually inspected for evidence ofdefect. Dimensions should be measured with slide calipers.The capacitor should be visually inspected.The capacitor should not be damaged when DC12.6kV isapplied between the lead wires for 1 to 5 sec.(Charge/Discharge currentV50mA)The capacitor is placed in the containerwith metal balls of diameter 1mm so thateach lead wire, short circuited, is keptabout 2.0mm off the metal balls as shownin the figure at right, and DC voltage of1.3kV is applied for 1 to 5 sec. betweencapacitor lead wires and metal balls.(Charge/Discharge currentV50mA)The insulation resistance should be measured withDC500±50V within 60±5 sec. of charging.The Q should be measured at 20°C with 1±0.2MHz andAC5V(r.m.s.) max.The capacitance measurement should be made at each stepspecified in the Table.2-25±3320±2485±2520±2About2.0mmMetal ballsThe capacitance should be measured at 20°C with 1±0.2MHzand AC5V(r.m.s.) max.9 Strength of Lead10 VibrationResistance11 Solderability of Leads12Soldering Effect(Non-Preheat)PullBendingAppearanceCapacitanceQAppearanceCapacitanceChangeDielectric Strength(Between LeadWires)Lead wire should not be cut off.Capacitor should not be broken.No marked defectWithin specified tolerance400+20C* 2 min. (30pF under)1000 min. (30pF min.)Lead wire should be soldered withuniform coating on the axial directionover 3/4 of the circumferential direction.No marked defectWithin ±2.5%Per item 4.* 1 "Room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa* 2 "C" expresses nominal capacitance value (pF).As shown in the figure at right, fix the body ofthe capacitor and apply a tensile weightgradually to each lead wire in the radialdirection of the capacitor up to 10N and keepit for 10±1 sec.Each lead wire should be subjected to 5N of weight and bent90° at the point of egress, in one direction, then returned to itsoriginal position and bent 90° in the opposite direction at therate of one bend in 2 to 3 sec.The capacitor should be firmly soldered to the supporting leadwire and vibrated at a frequency range of 10 to 55Hz, 1.5mm intotal amplitude, with about a 1-minute rate of vibration changefrom 10Hz to 55Hz and back to 10Hz. Apply for a total of 6 hrs.,2 hrs. each in 3 mutually perpendicular directions.The lead wire of a capacitor should be dipped into a ethanolsolution of 25wt% rosin and then into molten solder for 2±0.5sec. In both cases the depth of dipping is up to about 1.5 to2.0mm from the root of lead wires.Temp. of solder: Lead Free Solder (Sn-3Ag-0.5Cu) 245±5°CH63 Eutectic Solder 235±5°CThe lead wire should be immersed into the melted solder of350±10°C up to about 1.5 to 2.0mm from the main body for3.5±0.5 sec.Post-treatment: Capacitor should be stored for 1 to 2 hrs. atroom condition.* 1Continued on the following page.W1157
Page 7 and 8: !Note • Please read rating and !C
Page 57: !Note • Please read rating and !C

Safety Standard Certified Ceramic Capacitors/High Voltage ... - Murata

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?