INT'L Shortcut Cartridge Catalogue - Bibus SK, s.r.o.

More documents

Recommendations

Info

Cartridge Control Options General Purpose Controls (for use in systems where adjustment may be changed after installation.) L Standard Screw Adjustment O-ring seal on adjust screw. Adjust screw positively retained. Overset protection-pilot spring cannot go solid. K Handknob with Lock Knob Handknob and lock knob added to L control. Sun handknob kits for field conversion are available. (Except for counterbalance.) O Handknob with Panel Mount Special threaded cartridge hex body with panel nut for mounting cartridge through access hole in control panel. Handknob and lock knob included. Panel Hole: Series 1 cartridges 19,0 mm dia. Series 2 cartridges 25,4 mm dia. Panel nut hex size identical to cartridge hex size. C Tamper Resistant Factory Set Cover press-fit onto L control cartridge shoulder. Valves may be ordered in this configuration from Sun. Specify pressure setting on order. Setting stamped on cartridge hex. Sun kits for field conversion are available. Key Lock Kit Optional adjustment Key Lock Cover Kit for L controls allows adjustment to be locked with a key to prevent unauthorized changes in valve setting. Adjustment is easily accessible when lock assembly is removed. Requires replacement of 62,0 mm standard locknut with special 42,2 mm locknut which accepts lock assembly, and a new wire stop ring for overset protection. (Except for Series 0 and 79,2 mm counterbalance.) H Calibrated Handknob with Detent Lock Fully calibrated handknob for flow control cartridges. 40 radial calibrations per turn. Moveable zero indicator. (Minor disassembly required.) Rising detented locking collar positively locks adjustment knob against vibration or accidental tampering. Any desired setting may be recorded and repeated. U.S. Patent #4,577,831. Diameter 28,7 mm 35,1 mm 41,1 mm 41,1 mm Series 1 2 3 4 NCCB NCEB NCFB NCGB NCCC NCEC NCFC NCGC NFCC NFDC NFEC NFFC NFCD NFDD NFED NFFD FDBA FDCB FDEA FDFA Maximum Setting Limiter For limiting the maximum setting of cartridges with L adjust within their specified range (except Series 0 and counterbalance). These controls come in two 14,3 mm varieties: basic Maximum Setting Limiter and Maximum Setting Limiter with Handknob. Once kit is installed, the setting of cartridges can be adjusted within their specified range not to exceed the new permanent maximum setting. The maximum setting limiters can only be ordered as a kit at this time.Will be available as cartridge control options in future. Contact your Sun Distributor when ordering as cartridge control option. Special Purpose Controls (for use in systems where adjustment is seldom changed after installation) J Socket Head Set Screw with Cap 4,0 mm Hex F Wrench Adjustment Stem seal - Seal under locknut. Adjustment screw not retained. No overset protection. Stem seal - Seal under locknut. Adjusting screw is not retained. Overset protection-pilot spring cannot go solid. Counterbalance Cartridge Controls All Sun counterbalance cartridges are built with a leakproof adjustment - O-ring seals are on the adjusting screw-but are not designed for frequent adjustment in the field. Cartridges that are factory pre-set by Sun to a customer specified pressure setting are available and can be installed directly on a machine without the need for further adjustment. C Tamper Resistant Factory Set See “C” Control description above. 4,0 mm Hex 14,3 mm Hex 4,0 mm Hex 4,0 mm Hex 29,7 mm diameter 14,3 mm Hex 31,8 mm diameter Panel Hole 2,3 mm 7,6 mm L Standard Leakproof Screw Adjustment O-ring seal on adjust screw. Visit www.sunhydraulics.com for current list pricing and complete technical information on all Sun products. D Rising Stem Counts Full Turns to remove key or cover Zero Indicator Locking Collar Series 1, 2, 3: 4,0 mm Hex Series 4: 5,6 mm Hex Series 1, 2, 3: 14,3 mm Hex Series 4: 19,1 mm Hex 178 Int’l Shortcut Catalogue #999-901-312
Cartridge Control Kits Service Kit No. Description Adjustment Screw Kit 991-006 Adjustment Screw Kit 991-010 Tamper Resistant Cover (Zinc plated steel) 991-000 991-001 991-002 991-003 991-004 991-001-A00 991-002-A00 991-003-A00 991-004-A00 991-032 991-033 991-032-A00 991-033-A00 Key Lock Kit 993-008 K Handknob Kit (Plastic) 991-211 991-222 (Plastic) Panel Handknob Kit (Plastic) 991-215 Panel Handknob Kit (Plastic) 991-216 H Calibrated Handknob Kit (Plastic) 991-219 991-220 991-221 Use specifically with Control/Cartridge All F controls (Zinc plated steel) All J controls (Zinc plated steel) All Sun Models with L adjustment (Except Counterbalance, Series 1 and 2) Series 0 - 19,0 mm hex Series 2 - 28,6 mm hex Series 3 - 31,8 mm hex Series 4 - 41,0 mm hex Series 1 - 22,2 mm hex Series 2 - 28,6 mm hex (Stainless steel) Series 3 - 31,8 mm hex (Stainless steel) Series 4 - 41,0 mm hex (Stainless steel) Series 1 - 22,2 mm hex (Stainless steel) For Series 1 and 2, Counterbalance Series 1 - 22,2 mm hex (Zinc plated steel) Series 2 - 28,6 mm hex (Zinc plated steel) Series 1 - 22,2 mm hex (Stainless steel) Series 2 - 28,6 mm hex (Stainless steel) For all Sun cartridges with L adjustment (except Series 0 and counterbalance cartridges). Use this kit to adapt all L controls to K controls (except Series 0 and counterbalance cartridges). K control for Series 0 O controls All Series 1 cartridges 22,2 mm hex, M20 thread O controls All Series 2 cartridges 28,6 mm hex, 1”-14 thread H controls All series of flow controls FDCB, NCEB, NCEC, NFDC, NFDD only FDEA, FDFA, NCFB, NCFC, NCGB, NCGC, NFEC, NFED, NFFC, NFFD only FDBA, NCCB, NCCC, NFCC, NFCD only Adjust Screw Visit www.sunhydraulics.com for current list pricing and complete technical information on all Sun products. Int’l Shortcut Catalogue #999-901-312 179 Cap Cover Lock Assembly Key Locknut Handknob Assembly Description Notes Handknob Assembly Lock Knob Handknob Lockring O-ring Locknut Seal Seal Adjust Screw Wire Stop Ring Lock Knob Adapter Locknut Panel Nut Existing Cartridge To assure a complete seal on the stem - release all pressure on the cartridge after setting. Then... tighten locknut (and cap, on J). 1. Adjust valve to desired setting and tighten locknut. 2. Using an arbor press or a soft hammer, install cover until it seats on cartridge hex. 3. Cover is a press fit on cartridge shoulder. 1. Remove original wire stop ring and locknut. 2. Thread on the adapter locknut and install new wire stop ring through slot provided. 3. Adjust valve to desired setting and tighten adapter locknut. 4. Slide lock assembly over adapter, lock and remove key. Only cartridges date stamped “41” or later and originally supplied with plastic knobs. Lock knob snaps onto locknut furnished on cartridge. Only for cartridges originally supplied with an H handknob. Valves can not be modified in the field. Note: The H control is Only available for the cartridges shown to the left. Cartridge Control Kits continued on next page.
Page 1 and 2:
Over 35 New Products in this Catalo
Page 3 and 4:
Contents Model Codes printed in Red
Page 5 and 6:
2 1 2 2 2 1 1 1 2 1 2 1 2 1 2 Air P
Page 7 and 8:
Relief Valves DIRECT ACTING AND DIR
Page 9 and 10:
Relief Valves DIRECT ACTING, PILOT
Page 11 and 12:
Relief Valves PILOT OPERATED, BALAN
Page 13 and 14:
Page 15 and 16:
Relief Valves, Electro-Proportional
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Relief Valves Full Adjustment 5 Tur
Page 23 and 24:
Page 25 and 26:
2 1 2 2 3 2 1 2 1 3 T-8A Cav 2 3 3
Page 27 and 28:
Sequence Valves DIRECT ACTING WITH
Page 29 and 30:
Sequence Valves AIR CONTROLLED, PIL
Page 31 and 32:
Sequence Valves, Electro-Proportion
Page 33 and 34:
3 2 1 2 1 3 2 3 2 3 T-8A Cav Air Pi
Page 35 and 36:
Reducing Valves PILOT OPERATED, AIR
Page 37 and 38:
Reducing/Relieving Valves PILOT OPE
Page 39 and 40:
Reducing/Relieving Valves DIRECT AC
Page 41 and 42:
Reducing/Relieving Valves PILOT OPE
Page 43 and 44:
Reducing/Relieving Valves, Electro-
Page 45 and 46:
Reducing/Relieving Valves, Electro-
Page 47 and 48:
2 1 3 2 1 2 1 2 3 3 4 3 Ext. 1 Int
Page 49 and 50:
Pilot-to-Open Check Valves ATMOSPHE
Page 51 and 52:
2 2 2 2 2 2 2 4 2 4 2 3 3 3 3 3 3 3
Page 53 and 54:
Series 2 Series 3 Series 4 Series 2
Page 55 and 56:
Counterbalance Valves NON-VENTED, S
Page 57 and 58:
Counterbalance Valves NON-VENTED, S
Page 59 and 60:
Counterbalance Valves NON-VENTED, R
Page 61 and 62:
Counterbalance Valves VENTED, 280 B
Page 63 and 64:
2 2 4 2 4 2 3 3 3 3 1 1 1 1 Load Co
Page 65 and 66:
Load Control: Load Reactive Valves
Page 67 and 68:
Load Control: Load Reactive Valves
Page 69 and 70:
2 2 3 3 4 1 1 Load Control: Balance
Page 71 and 72:
Load Control: Balanced VENTED, NON-
Page 73 and 74:
2 1 2 1 2 1 2 1 2 1 3 3 Int’l Sho
Page 75 and 76:
Check Valves FREE FLOW, SIDE-TO-NOS
Page 77 and 78:
Check Valves FREE FLOW, SIDE-TO-NOS
Page 79 and 80:
1 1 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2
Page 81 and 82:
Flow Control Valves FULLY ADJUSTABL
Page 83 and 84:
Flow Control Valves FIXED ORIFICE,
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Flow Control Valves VENTABLE, FIXED
Page 91 and 92:
Flow Control Valves, Electro-Propor
Page 93 and 94:
3 3 3 3 4 2 4 2 4 2 4 2 Flow Divide
Page 95 and 96:
Flow Divider / Combiner Valves DIVI
Page 97 and 98:
Flow Divider / Combiner Valves DIVI
Page 99 and 100:
4 4 T-8A Cav 4 2 1 2 1 2 1 3 3 3 3
Page 101 and 102:
Logic Elements BALANCED POPPET, NOR
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Logic Elements UNBALANCED POPPET, V
Page 111 and 112:
Logic Elements UNBALANCED POPPET, P
Page 113 and 114:
Logic Elements NORMALLY CLOSED, MOD
Page 115 and 116:
Logic Elements BI-DIRECTIONAL, MODU
Page 117 and 118:
1 1 4 T-8A 4 T-8A 2 1 3 2 1 3 2 1 3
Page 119 and 120:
Directional Valves 2-WAY AND 3-WAY,
Page 121 and 122:
Directional Valves 2-WAY AND 3-WAY
Page 123 and 124:
Directional Valves 2-WAY AND 3-WAY,
Page 125 and 126:
Directional Valves 3-WAY, 2-POSITIO
Page 127 and 128: Directional Valves 2-WAY POPPET, WI
Page 129 and 130: Directional Valves 3-POSITION, 4-WA
Page 131 and 132: 2 2 1 Solenoid Operated Cartridge V
Page 133 and 134: Solenoid Operated Cartridge Valves
Page 141 and 142: 1 2 2 1 2 Air Pilot 2 1 Normally Op
Page 143 and 144: Pilot Control Valves DIRECT ACTING,
Page 145 and 146: Pilot Control Valves FLOW CONTROL,
Page 147 and 148: Pilot Control Valves 2-WAY, HYDRAUL
Page 149 and 150: Pilot Control Valves 2-WAY, AIR OPE
Page 151 and 152: Pilot Control Valves 3-WAY, 2-POSIT
Page 153 and 154: Pilot Control Valves 3-WAY, 2-POSIT
Page 155 and 156: 1 Ext. 2 1 2 Ext. 1 2 3 1 2 3 2 4 3
Page 157 and 158: Shuttle Valves BACK-TO-BACK CHECK/S
Page 159 and 160: Shuttle Valves BACK-TO-BACK CHECK/S
Page 161 and 162: Shuttle Valves HIGH SIDE, 3-POSITIO
Page 163 and 164: 2 1 3 2 2 1 3 2 1 2 1 4 2 3 1 3 1 I
Page 165 and 166: Circuit Savers AIR BLEED AND START-
Page 167 and 168: Circuit Savers CHECK, PILOT-TO-CLOS
Page 169 and 170: Circuit Savers ACCUMULATOR SENSE, P
Page 171 and 172: 1 1 1 1 2 2 2 2 4 T-8A 4 3 3 3 3 In
Page 173 and 174: Hybrid Valves DIRECT ACTING RELIEF,
Page 175 and 176: Hybrid Valves PILOT OPERATED, BALAN
Page 177: Int’l Shortcut Catalogue #999-901
Page 181 and 182: Cartridge Control Kits Service Kit
Page 183 and 184: Cavity Plugs It is sometimes desira
Page 185 and 186: Cavity Plugs Plugs for Six Port Cav
Page 187 and 188: Sun Coil Options for Solenoids (Met
Page 189 and 190: Sun Coil Options with Embedded Elec
Page 191 and 192: Sun Coil 790-***** Part Numbering S
Page 193 and 194: Sun Model Code System Sun cartridge
Page 195 and 196: Model Code Index Model Code Cavity
Page 197 and 198: Model Code Index Model Code Cavity
Page 199 and 200: Warranty Sun Hydraulics Limited man
Page 201: Mexico COUNTRY DISTRIBUTOR Componen
show all

INT'L Shortcut Cartridge Catalogue - Bibus SK, s.r.o.

Create successful ePaper yourself

Delete template?

Save as template?