INT'L Shortcut Cartridge Catalogue - Bibus SK, s.r.o.
INT'L Shortcut Cartridge Catalogue - Bibus SK, s.r.o.
INT'L Shortcut Cartridge Catalogue - Bibus SK, s.r.o.
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Service Kit<br />
Number<br />
Description<br />
Adjustment<br />
Screw Kit<br />
991-112-003 Viton<br />
991-112-007 Buna-N<br />
Adjustment<br />
Screw Kit<br />
991-212-003 Viton<br />
991-212-007 Buna-N<br />
Maximum<br />
Setting<br />
Limiter<br />
(Zinc plated steel)<br />
991-022<br />
Lockwire Kit<br />
991-012<br />
<strong>Cartridge</strong> Control Kits<br />
Position Switch<br />
Protective Cover<br />
(6061-T6 Aluminium)<br />
991-043<br />
Use specifically with<br />
Control/<strong>Cartridge</strong><br />
CKCA-L** CKCD-L**<br />
CKCB-L** CPCA-L**<br />
CKCC-L**<br />
CKEA-L** CKED-L**<br />
CKEB-L** CPEA-L**<br />
CKEC-L**<br />
All models with an L<br />
adjustment control (Except<br />
Series 0 and counterbalance.)<br />
The maximum setting limiters<br />
can only be ordered as a kit at<br />
this time. Will be available as<br />
cartridge control options in<br />
the future with customer<br />
specified settings.<br />
Contact your Sun<br />
Distributor when ordering<br />
as cartridge control option.<br />
All M, Q and R controls<br />
(except solenoid operated<br />
cartridges).<br />
LOHC-Z**<br />
53,1 mm<br />
38,9 mm<br />
Manual<br />
Release<br />
Screw<br />
Locknut<br />
Description<br />
Back-up<br />
Ring<br />
Visit www.sunhydraulics.com for current list pricing and complete technical information on all Sun products.<br />
Seal<br />
Pin (2) Cap Existing <strong>Cartridge</strong><br />
Locking Wire<br />
53,1 mm<br />
38,9 mm<br />
Lead Seal<br />
(4) 1/4-20 SCHS x 101,6 mm LG<br />
95,3 mm<br />
Only cartridges date stamped “62”<br />
or earlier.<br />
Installation Instructions:<br />
Kit consists of 2 Driv-Lok pins<br />
(811-001-011), Hex Cap<br />
(375-020). To prevent any<br />
damage to nose end and/or any<br />
moving parts, only install this<br />
kit while cartridge is screwed<br />
into a cavity.<br />
1. Set adjustment to desired level<br />
within recommended range of<br />
valve and tighten jam nut to<br />
12Nm.<br />
2. Remove maximum setting<br />
stop ring from the adjust<br />
screw.<br />
3. Thread hex cap onto the adjust<br />
screw until it bottoms out<br />
against jam nut and tighten to<br />
12 Nm.<br />
4. Insert one of the Driv-Lok pins<br />
into the hex cap holes and tap<br />
into place using a hammer<br />
until flush. Repeat procedure<br />
with second Driv-Lok pin.<br />
5. Install is now completed.<br />
Installation:<br />
Threaded holes will need to be<br />
machined in the manifold to install<br />
cover.<br />
Number of Holes: 4<br />
Mounting Hole Thread:<br />
.250-20 UNC -2B<br />
Mounting Hole Depth: 13,5 mm<br />
182 Int’l <strong>Shortcut</strong> <strong>Catalogue</strong> #999-901-312