ControlNet-to-DeviceNet Linking Device User Manual, 1788 ...

More documents

Recommendations

Info

.2-2 Installing the 1788-CN2DNATTENTION!This module contains ESD (Electrostatic Discharge)sensitive parts and assemblies. Static controlprecautions are required when installing or testingthis assembly. Component damage may result ifthese procedures are not followed.Because of the variety of uses for the product described in thispublication, those responsible for the application and use of thiscontrol equipment must satisfy themselves that all necessary stepshave been taken to assure that each application and use meets allperformance and safety requirements, including any applicable laws,regulations, codes, and standards.The illustrations, sample programs, and layout examples shown in thismanual are intended solely for purposes of example. Since there aremany variables and requirements associated with any particularinstallation, Allen-Bradley does not assume responsibility or liability(to include intellectual property liability) for actual use based uponthe examples shown in this publication.Installation ProcedureThe CN2DN module should be mounted on a standard 35 mm steelDIN rail. Follow the steps below to mount the CN2DN on the DIN rail.IMPORTANTYou must use a steel DIN rail (A-B P/N 199-DR1 orequivalent) to meet the 1788-CN2DN’s vibrationspecifications. DO NOT use an aluminum DIN rail.1. Press the module straight onto the DIN rail at the desired location.Be sure that both latches snap into place.Figure 2.1 - Mounting the CN2DN Module on the DIN RailWall or SupportPRESS ONDIN RailCN2DN ModulePublication 1788-UM053A-EN-P - July 2001
Installing the 1788-CN2DN 2-32. Use the supplied end anchors to lock the module into place.Figure 2.2 - End Anchors and Mounting TabsMounting TabsEnd AnchorEnd AnchorLatchesMounting Tabs30901-MNote that for very high shock applications the module may be boltedto a panel through the four mounting tabs on the base. See page 2-10for dimensions.Removing the CN2DN moduleTo remove the CN2DN module from the DIN rail, simultaneously pullthe 2 latches away from the rail and pull the module off the panel.(Note: It may require two screwdrivers to pry the latches open.)Connecting PowerThe CN2DN linking device requires 18-30V dc input power. TheCN2DN filters and regulates the supplied power. The powerconnector is a 4-pin redundant screw terminal connector.Publication 1788-UM053A-EN-P - July 2001
Page 1 and 2: ControlNet-to-DeviceNetLinking Devi
Page 3 and 4: Throughout this manual we use these
Page 5: Rockwell AutomationSupportRockwell
Page 8: P-2 About This User ManualAbout the
Page 14 and 15: 1-2 Module DescriptionRequired Soft
Page 16 and 17: 1-4 Module DescriptionPublication 1
Page 20 and 21: 2-4 Installing the 1788-CN2DNThe pi
Page 22 and 23: 2-6 Installing the 1788-CN2DNFigure
Page 24 and 25: 2-8 Installing the 1788-CN2DNSettin
Page 26 and 27: 2-10 Installing the 1788-CN2DNMount
Page 28 and 29: 3-2 ControlLogix ControlNet Configu
Page 36 and 37: 3-10 ControlLogix ControlNet Config
Page 38 and 39: 4-2 PLC-5 ControlNet ConfigurationY
Page 40 and 41: 4-4 PLC-5 ControlNet ConfigurationI
Page 42 and 43: 4-6 PLC-5 ControlNet ConfigurationN
Page 44 and 45: 4-8 PLC-5 ControlNet ConfigurationT
Page 46 and 47: 4-10 PLC-5 ControlNet Configuration
Page 48 and 49: 5-2 SLC 500 ControlNet Configuratio
Page 56 and 57: 6-2 RSNetWorx for DeviceNet Configu
Page 62 and 63: A-2 LED Status IndicatorsLinking Ac
Page 64 and 65: A-4 LED Status IndicatorsPublicatio
Page 66 and 67: B-2 1788-CN2DN Input, Output, and S
Page 70 and 71:
B-6 1788-CN2DN Input, Output, and S
Page 72 and 73:
B-8 1788-CN2DN Input, Output, and S
Page 74 and 75:
2 IndexPPLC-5 ControlNet configurat
Page 76:
PLEASE FASTEN HERE (DO NOT STAPLE)O
show all

ControlNet-to-DeviceNet Linking Device User Manual, 1788 ...

Create successful ePaper yourself

Delete template?

Save as template?