56701-IPI only

More documents

Recommendations

Info

VENTINGNOTE: Horizontal sections require 1/4” (6 mm) rise for every 12” (305 mm) of travel.NOTE: Flange on top stand-off must be bent upwards to a 90˚ angle when top venting.NOTE: Page 22 has information on restrictor installation in conjunction with venting installation. Page 51 has information onrestrictor recommendations depending on burner flame appearance and instructions on installation after venting is completed.IMPORTANT: If top venting, follow instructions on pages 16-17 to convert fireplace from rear vent ready to top vent ready.CAUTION: This gas appliance must not be connected to or joined with any other chimney flue serving another appliance.HORIZONTAL TERMINATIONS (top vent)Max: 14 ft. (4.27m)Min: 6” (152 mm)90° ELBOWTERMINATION CAPFigure 19aHORIZONTAL TERMINATIONS (rear vent)Min: 6” (152 mm)Max: 24” (610 mm)TERMINATION CAPFigure 19bPAGE 19
HORIZONTAL TERMINATIONSVENTINGNOTE: Horizontal sections require 1/4” (6 mm) rise for every 12” (305 mm) of travel.NOTE: Flange on top stand-off must be bent upwards to a 90˚ angle when top venting.NOTE: Page 22 has information on restrictor installation in conjunction with venting installation. Page 51 has information onRestrictor recommendations depending on burner flame appearance and instructions on installation after venting is completed.IMPORTANT: If top venting, follow instructions on pages 16-17 to convert fireplace from rear vent ready to top vent ready.CAUTION: This gas appliance must not be connected to or joined with any other chimney flue serving another appliance.TYPICAL CORNER INSTALLATION90° elbow + horizontal pipe + termination cap.VENTING DIMENSIONS FOR MINIMUM CORNER INSTALLATIONSVent Opening Dimensions: Refer to vent pipe manufacturer's instructionsPIPE90° ELBOWHORIZONTALTERMINATION CAPFigure 20aPAGE 20
Page 1 and 2: INSTALLATION AND OPERATION MANUALIN
Page 3 and 4: INTRODUCTIONTABLE OF CONTENTSVENTIN
Page 5 and 6: FEATURESSTANDARD FEATURESHigh effic
Page 7 and 8: SPECIFICATIONSFIREPLACE DIMENSIONSL
Page 9 and 10: NAILING FLANGE ASSEMBLY & INSTALLAT
Page 11 and 12: FRAMINGDetermine exact position of
Page 13 and 14: NON-COMBUSTIBLE ZONE:MANTEL REQUIRE
Page 15 and 16: GAS LINE CONNECTIONGAS CONVERSIONTh
Page 17 and 18: VENTING (Top vent conversion instru
Page 19: VENTINGIMPORTANT: Consult the local
Page 23 and 24: VENTINGVERTICAL VENTING (rear vent)
Page 25 and 26: VENTING#700 SERIES DIRECT VENT TERM
Page 27 and 28: 1. Terminations against vinyl sidin
Page 29 and 30: #TRF-500A LOG SET INSTALLATIONATTEN
Page 31 and 32: CONTROL BOARD REMOVALCAUTION: If bu
Page 33 and 34: GRILL SETINSTALLATION12 Slide flang
Page 35 and 36: 56701 LIGHTING AND SHUTDOWNFOR YOUR
Page 37 and 38: 56701 LIGHTING AND SHUTDOWN (cont.)
Page 39 and 40: 56701-IPI WIRING SCHEMATICSIMPORTAN
Page 41 and 42: 56701-IPI CONTROL MODULE COMPONENTS
Page 43 and 44: ELECTRICAL WARNING AND INFORMATION:
Page 45 and 46: 56701-IPI REMOTE RECEIVER INFORMATI
Page 47 and 48: 56701-IPI LIGHTING AND SHUTDOWNFOR
Page 49 and 50: PRESSURE TESTING (56701-IPI)IMPORTA
Page 51 and 52: FLAME APPEARANCE:FINALIZING THE INS
Page 53 and 54: MAINTENANCEThe appliance is require
Page 55 and 56: TROUBLESHOOTING (56701 only)BURNER
Page 57 and 58: TROUBLESHOOTING (56701-IPI only)MAI
Page 59 and 60: CONVERSION KIT INSTRUCTIONS (56701
Page 61 and 62: CONVERSION KIT INSTRUCTIONS (56701-
Page 63 and 64: Replacement parts are available thr
Page 65: LIFETIME WARRANTYPAGE 64

56701-IPI only

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?