Adjustable Frequency AC Drive

More documents

Recommendations

Info

1-22 Installation/WiringEN61000-3-2• 0.75 kW (1 HP) 240V 1-Phase and 3-Phase drives and 0.37 kW (0.5HP) 240V 1-Phase drives are suitable for installation on a private lowvoltage power network. Installations on a public low voltage powernetwork may require additional external harmonic mitigation.• Other drive ratings meet the current harmonic requirements ofEN61000-3-2 without additional external mitigation.
Chapter 2Start UpThis chapter describes how to start up the PowerFlex 4 Drive. Tosimplify drive setup, the most commonly programmed parameters areorganized in a single Basic Program Group.Important: Read the General Precautions section before proceeding.!ATTENTION: Power must be applied to the drive to perform thefollowing start-up procedures. Some of the voltages present are atincoming line potential. To avoid electric shock hazard or damage toequipment, only qualified service personnel should perform thefollowing procedure. Thoroughly read and understand the procedurebefore beginning. If an event does not occur while performing thisprocedure, Do Not Proceed. Remove All Power including usersupplied control voltages. User supplied voltages may exist even whenmain AC power is not applied to the drive. Correct the malfunctionbefore continuing.❏❏❏❏Prepare For Drive Start-UpBefore Applying Power to the Drive1. Confirm that all inputs are connected to the correct terminals and aresecure.2. Verify that AC line power at the disconnect device is within the ratedvalue of the drive.3. Verify that any digital control power is 24 volts.4. Verify that the Sink (SNK)/Source (SRC) Setup DIP Switch is set tomatch your control wiring scheme. See Figure 1.5 on page 1-13 forlocation.Important: The default control scheme is Source (SRC). The Stopterminal is jumpered (I/O Terminals 01 and 11) to allowstarting from the keypad. If the control scheme is changedto Sink (SNK), the jumper must be removed from I/OTerminals 01 and 11 and installed between I/O Terminals01 and 04.❏5. Verify that the Stop input is present or the drive will not start.Important: If I/O Terminal 01 is used as a stop input, the jumperbetween I/O Terminals 01 and 11 must be removed.
Page 2 and 3: Important User InformationSolid sta
Page 4 and 5: soc-2The information below summariz
Page 7 and 8: PrefaceOverviewThe purpose of this
Page 9 and 10: Overview P-3General Precautions!ATT
Page 11 and 12: Chapter 1Installation/WiringThis ch
Page 13 and 14: Installation/Wiring 1-3AC Supply So
Page 15 and 16: Installation/Wiring 1-5Ground Fault
Page 17 and 18: Installation/Wiring 1-7Table 1.D Mi
Page 19 and 20: Installation/Wiring 1-9Reflected Wa
Page 21 and 22: Installation/Wiring 1-11I/O Wiring
Page 23 and 24: Figure 1.5 Control Wiring Block Dia
Page 25 and 26: Installation/Wiring 1-15Input2 Wire
Page 27 and 28: Installation/Wiring 1-17Typical Mul
Page 29 and 30: Installation/Wiring 1-19Accel/Decel
Page 31: Installation/Wiring 1-21Essential R
Page 35 and 36: Start Up 2-3Integral Keypad➏➋
Page 37 and 38: Chapter 3Programming and Parameters
Page 39 and 40: Programming and Parameters 3-3Displ
Page 45 and 46: Programming and Parameters 3-9Basic
Page 47 and 48: Programming and Parameters 3-11Basi
Page 49 and 50: Programming and Parameters 3-13Adva
Page 51 and 52: Advanced Program Group (continued)A
Page 61 and 62: Programming and Parameters 3-25A110
Page 63 and 64: Programming and Parameters 3-27Para
Page 65 and 66: Chapter 4TroubleshootingChapter 4 p
Page 67 and 68: Troubleshooting 4-3Fault Descriptio
Page 69 and 70: Troubleshooting 4-5Common Symptoms
Page 71 and 72: Troubleshooting 4-7Motor and/or dri
Page 73 and 74: Supplemental Drive InformationFor i
Page 75 and 76: Supplemental Drive Information A-3C
Page 77 and 78: Accessories and DimensionsFor infor
Page 79 and 80: Accessories and Dimensions B-3Table
Page 81 and 82: Accessories and Dimensions B-5Produ
Page 83 and 84:
Accessories and Dimensions B-7Figur
Page 85 and 86:
SURFACES MAY BEAccessories and Dime
Page 87 and 88:
Accessories and Dimensions B-11Figu
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Appendix CRS485 (DSI) ProtocolPower
Page 95 and 96:
RS485 (DSI) Protocol C-3Writing (06
Page 97 and 98:
RS485 (DSI) Protocol C-5Reading (03
Page 99 and 100:
Appendix DRJ45 DSI Splitter CableTh
Page 101 and 102:
RJ45 DSI Splitter Cable D-3Connecti
Page 103 and 104:
IndexAAC SupplyGround, 1-4Source, 1
Page 105 and 106:
Index-3Start/Stop, Repeated, 1-11St
Page 108:
www.rockwellautomation.comPower, Co
show all

Adjustable Frequency AC Drive

Create successful ePaper yourself

Delete template?

Save as template?