Indoor Unit Outdoor Unit CS-PS9NKV CS-PS12NKV CS ... - Panasonic

More documents

Recommendations

Info

13. Servicing Mode13.1 Auto Off/On ButtonAuto OFF/ONButton PressedAuto Operation5 secTest Run Operation(Forced Cooling Operation)Auto OFF/ONButton PressedStop1 AUTO OPERATION MODEThe Auto Operation will be activated immediately once the Auto OFF/ON button is pressed. This operationcan be used to operate air conditioner with limited function if remote control is misplaced or malfunction.2 TEST RUN OPERATION (FOR PUMP DOWN/SERVICING PURPOSE)The Test Run Operation will be activated if the Auto OFF/ON button is pressed continuously for more than 5seconds. A “beep” sound will be heard at the fifth seconds, in order to identify the starting of this operation.The Auto OFF/ON button may be used together with remote control to set / change the advance setting of airconditioner operation.Main unit always continue Test Run (forced cooling) operation.5 sec 8 sec 11 sec 16 secAuto Operation Test Run Operation Remote Control Number Remote Control Receiving(Forced Cooling Operation) Switch ModeSound OFF/ONBeep Beep x 2 Beep x 3 Beep x 4Press “AC Reset”, thenany key at remote controlPress “AC Reset”, then“Check” at remote control3 REMOTE CONTROL NUMBER SWITCH MODEThe Remote Control Number Switch Mode will be activated if the Auto OFF/ON button is pressedcontinuously for more than 11 seconds (3 “beep” sounds will occur at 11 th seconds to identify the RemoteControl Number Switch Mode is in standby condition), press “AC Reset” button and then press any button atremote control to transmit and store the desired transmission code to the EEPROM.There are 4 types of remote control transmission code could be selected. The indoor unit will only operatewhen received signal with same transmission code from remote control. This could prevent signalinterference when there are 2 or more units installed nearby together.To change remote control transmission code, short or open jumpers at the remote control printed circuitboard.Remote Control Printed Circuit BoardJumper A (J-A) Jumper B (J-B) Remote Control No.Short Open A (Default)Open Open BShort Short COpen Short D4 REMOTE CONTROL RECEIVING SOUND OFF/ON MODEThe Remote Control Receiving Sound OFF/ON Mode will be activated if the Auto OFF/ON button is pressedcontinuously for more than 16 seconds (4 “beep” sounds will occur at 16 th seconds to identify the RemoteControl Receiving Sound OFF/ON Mode is in standby condition) and press “AC Reset” button and then press“Check” button at remote control.Press Auto OFF/ON button to toggle remote control receiving sound.- Short “beep”: Turn ON remote control receiving sound.- Long “beep”: Turn OFF remote control receiving sound.After Auto OFF/ON button is pressed, the 20 seconds counter for Remote Control Receiving Sound OFF/ONMode is restarted.54
13.2 Remote Control Button13.2.1 SET Button• To check remote control transmission code and store the transmission code to EEPROMo Press “Set” button for more than 10 seconds by using pointero Press “Timer Set” button unit a “beep” sound is heard as confirmation of transmission code change.13.2.2 RESET (RC) Button• To clear and restore the remote control setting to factory default.o Press once to clear the memory13.2.3 TIMER ▲• To change indoor unit indicators’ intensity:o Press continuously for 5 seconds.13.2.4 TIMER ▼• To change remote control display from Degree Celsius (°C) to Degree Fahrenheit (°F)o Press continuously for 10 seconds.55
Page 1 and 2:
Order No: PHAAM1201103C3Indoor Unit
Page 3 and 4: 1. Safety Precautions• Read the f
Page 5 and 6: 2. SpecificationCoolingModelIndoor
Page 7 and 8: CoolingModelIndoor CS-PS18NKV CS-PS
Page 9 and 10: 3. Location of Controls and Compone
Page 11 and 12: 4.1.2 CS-PS18NKV CS-PS24NKV11
Page 13 and 14: 4.2.3 CU-PS24NKV13
Page 15 and 16: 5.2 CS-PS18NKV CU-PS18NKV CS-PS24NK
Page 17 and 18: 6.2 CS-PS12NKV CU-PS12NKV17
Page 19 and 20: 6.4 CS-PS24NKV CU-PS24NKV19
Page 23 and 24: 7.2.2 CU-PS12NKVResistance of Compr
Page 25 and 26: 7.2.4 CU-PS24NKVResistance of Compr
Page 33 and 34: 9.1.1.2 CS-PS18NKV CS-PS24NKV9.1.2
Page 35 and 36: 9.2.1.2 CU-PS12NKV35
Page 37 and 38: 9.2.1.4 CU-PS24NKV37
Page 39 and 40: 10. Installation Instruction10.1 Se
Page 41 and 42: 10.2.3 Indoor Unit Installation10.2
Page 43 and 44: Note:• Isolating Devices (Disconn
Page 45 and 46: 10.3.3 Evacuation of the EquipmentW
Page 47 and 48: 11. Operation Control11.1 Basic Fun
Page 49 and 50: 11.4 Airflow Direction• There are
Page 51 and 52: 12. Protection Control12.1 Restart
Page 53: 12.10 Cooling Overload Control• P
Page 57 and 58: 14.1.1 Relationship between the con
Page 59 and 60: 14.3 Error Code TableDiagnosisEmerg
Page 61 and 62: 14.4.2 H12 (Indoor/Outdoor Capacity
Page 63 and 64: 14.4.4 H15 (Compressor Temperature
Page 65 and 66: 14.4.6 H19 (Indoor Fan Motor - DC M
Page 67 and 68: 14.4.8 H27 (Outdoor Air Temperature
Page 69 and 70: 14.4.10 H33 (Unspecified Voltage be
Page 71 and 72: 14.4.12 H99 (Indoor Freeze Preventi
Page 73 and 74: 14.4.14 F90 (Power Factor Correctio
Page 75 and 76: 14.4.16 F93 (Compressor Rotation Fa
Page 77 and 78: 14.4.18 F96 (IPM Overheating)Malfun
Page 79 and 80: 14.4.20 F98 (Input Over Current Det
Page 81 and 82: 15. Disassembly and Assembly Instru
Page 83 and 84: 15.1.4 To remove control board12. R
Page 85 and 86: WARNINGHigh Voltage is generated in
Page 87 and 88: 15.2.4 To remove control boardFigur
Page 89 and 90: 16. Technical Data16.1 Operation Ch
Page 91 and 92: 16.1.2 CS-PS12NKV CU-PS12NKV• Coo
Page 97 and 98: 17. Exploded View and Replacement P
Page 99 and 100: 17.1.2 CS-PS18NKV CS-PS24NKVNoteThe
Page 101 and 102: 17.2 Outdoor Unit17.2.1 CU-PS9NKVNo
Page 103: 17.2.2 CU-PS12NKVNoteThe above expl
Page 106 and 107:
REF. NO. DESCRIPTION & NAME QTY CU-
Page 108:
REF. NO. DESCRIPTION & NAME QTY CU-
show all

Indoor Unit Outdoor Unit CS-PS9NKV CS-PS12NKV CS ... - Panasonic

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?