USB IO HID Datasheet - Delcom Products Inc.

More documents

Recommendations

Info

Delcom Products Inc.USBIOHID DatasheetRevision 4 – 4/7/20095 Programmed Features5.1 Basic I/OThe USB HID I/O chips provide general 8 bit input/output commands as well as individual setand reset commands of each pin. See write command 1,2,10,11, 12 and read commands100.5.2 Write data with StrobeSee write commands 13, 14, 15 and 16.The write strobe feature allows the USB I/O chip to interface to another device by using astandard 8-bit data bus with a strobe pin. The data is placed on port 0 and the strobe isselectable on one of the port 1 pins. Theses functions allow one to eight data bytes to be senton either a positive and negative strobe (pulse). The write strobe functions support anoptional acknowledge signal.Commands 13 and 14 produces the following sequence; 1) Data in is written to Port 0. 2) Thestrobe pin is toggled active for 1.5us. Optionally, if the acknowledge pin is enabled the strobepin will wait while the acknowledge pin is held low (See command 10-40 bit 3). 3) Then thestrobe pin is toggled non-active. 4) And finally 0xFF is written to Port 0. The strobe pin andthe data on port 0 must be initially preset to there no active states before using this function.Port0 should be preset to 0xFF.Commands 15 and 16 produces the following sequence; 1) Data in Data Extension is writtento Port 0 LSB first. 2) The strobe pin is set active for 1.5us. If the acknowledge pin is enabledthe strobe pin will wait while the acknowledge pin is held low (See command 10-40 bit 3). 3)Then the strobe pin is made non-active. 4) And finally 0xFF is written to Port 0. 4) Systemthen delays for the specified time set in Data LSB byte. 5) Then the process is repeated till alldata bytes in the Data Extension have been sent. The delay is equal to8.25us+(0.75us*DelayValue) Example: Command 8,18,10,15,10,1,4,0,0,0,0 will send 4 bytesof data (all zeros here) on a high strobe on pin one of port one with a delay of 15.75us. Thestrobe pin and the data on port 0 must be initially preset to there no active states before usingthis function.5.3 Read Data with StrobeSee read commands 1 and 2.The read strobe feature allows the USB I/O chip to interface to another device by using astandard 8-bit data bus with a strobe pin. The data is captured on port 0 with a active strobeon port1. The strobe pin can be either active high or low. Note before using this command,users should preset Port1 to 0xFF to place Port1 in input mode. The read data strobecommand will produce the following sequence. 1) The selected strobe pin on Port 1 is madeactive. 2) Delay for 1.5us. 3) Data us latched on Port0 and stored. 4) The strobe pin isreleased.5.4 Clock GeneratorThese functions generate a clock source with variable frequency and duty cycle. Up to fourseparate clocks can be configured. The clock outputs can be selected on port 1 pins 0USBIOHID.pdf Copyright © DELCOM PRODUCTS INC. 2009. All Rights Reserved. Page 6 of 34Delcom Products Inc. 200 William St STE302 – Port Chester NY 10573 USA (914)934-5170 www.delcomproducts.com
Delcom Products Inc.USBIOHID DatasheetRevision 4 – 4/7/2009through 3. Clock pins can be preset to a predefined state. Use command 20 to enable thisfeature.See write commands 19, 20, 21, 22, 23, 24, 25, 26, 27, 28 and 29.Frequency and duty commands (21-24). The LSB data value sets the period when the portpin is high and the MSB data value sets the period when the port pin is low. The defaultresolution of the period is 10ms, but this can be changes with the prescalar command (19).The resolution of the duty cycle is 0.39 percent.5.5 PWMThis feature allows for a PWM function on ports1 pins P1.0 though P1.3. Use write command34 to configure the PWM feature. To enabled the PWM feature on a pin you must write alow(zero) to that pin. A PWM value of 100(100%) will keep the pin low infinitely. Any valueless than 100 will produce a PWM on the selected port pin. To disable the PWM function youmust set the duty to 100 (100%). When the duty is set to 100 (100%) the pin function is it’snormal state (high or low depend on how it is set). See write command 34.5.6 Port SetupThese features allow the user to place the I/O in one of 4 modes. Each pin on ports 0 and 1can be set independently. The boot up default is mode C. To change the port pin modes usewrite commands 45-48.GPIO Mode tableModeMode 1 ValueCommand 46,48Mode 0 ValueCommand 45,47Port type whendata out is lowPort type whendata out is highA 0 0 Hi-Z / CMOS Hi-Z / TTLB 0 1 Medium (8mA)Sink / CMOSC – DefaultBoot up State1 0 Low (2mA)Sink / CMOSHigh (30mA)Drive / CMOSPull up (14K) /CMOSD 1 1 High (50mA)Sink / CMOSHigh (30mA)Drive / CMOSMaximum cumulative source drive current for all GPIO is 30mA.Maximum cumulative sink drive current for all GPIO is 70mA.See http://www.delcomproducts.com/downloads/cy7c637xx-B.pdf for more GPIO details.5.7 Read BufferThis feature allows the USB I/O chip to interface to a device using a standard 8-bit data busand a read strobe pin. Data is read on port 0 with a read strobe (pulse) on one of theselectable port 1 pins. The data read buffer is 7 bytes deep. If the read data buffer is full,new data will not be accepted and the over flow flag will be set. Note this function cannot beused while the RS232 functions are in uses. See read command 5.USBIOHID.pdf Copyright © DELCOM PRODUCTS INC. 2009. All Rights Reserved. Page 7 of 34Delcom Products Inc. 200 William St STE302 – Port Chester NY 10573 USA (914)934-5170 www.delcomproducts.com
Page 1: Delcom Products Inc.USBIOHID Datash
Page 4 and 5: Delcom Products Inc.USBIOHID Datash
Page 8 and 9: Delcom Products Inc.5.8 Scratch Pad
Page 16 and 17: Delcom Products Inc.LSBData = Enabl
Page 30 and 31: Delcom Products Inc.Write example.U
Page 34: Delcom Products Inc.Appendix B. Not

USB IO HID Datasheet - Delcom Products Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?