DaqLink User Guide - Contika

More documents

Recommendations

Info

• DaqLink software CD containing user guide1.2.1. The Data LoggerThere are two data logger models compatible with theDaqLink system. These loggers support up to four externalsensors and two internal sensors, temperature and humidity,depending on the specific model. Data is recorded and storedto the logger’s internal memory and transmitted over thenetwork to the DaqLink software running on the PC.The data logger is programmed to consume as little power aspossible during operation, in order to conserve the battery life.When not transmitting or recording data the units are in sleepmode and they wake up when needed.The battery for the DBSA710 and DBSA720 is rechargeableand can run up to several months on one charge, dependingon the logger configuration.Refer to section 3.5.3 for more information.Note: Battery life depends on the logger sampling rate,transmission rate, type of sensor, and number of measuredsensors.3
DaqLink Data LoggersPart Number: DBSA720Four external channel data logger withtwo internal sensors, Humidity andTemperatureMemory Capacity: ~59,000 samplesPower supply: AC or battery operatedPart Number: DBSA710Four external channel data logger withinternal Temperature sensorMemory Capacity: ~59,000 samplesPower supply: AC or battery operated1.2.2. Hardware AccessoriesThe DaqLink system includes the following accessories:• Mini-USB cable for connecting data logger to PC• Power adapter to power the data logger4
Page 1 and 2: Committedto QualityDaqLink 4 Channe
Page 3 and 4: Contacting Fourier Systems technica
Page 5 and 6: 3.2. Data Logger External Connectio
Page 7 and 8: 4.6.2. Email Settings Tab 604.6.3.
Page 9 and 10: APPENDIX D: FIGURES AND TABLES 118
Page 11: The DaqLink system is powered by th
Page 15 and 16: Chapter 2:DaqLinkImplementation Gui
Page 17 and 18: 4. Check for DaqLink updates. Go to
Page 19 and 20: If the loggers will run from the AC
Page 21 and 22: On the Device Setup and Alarm Setup
Page 23 and 24: Figure 4: Online data - Graph viewF
Page 25 and 26: • Double-clicking the individual
Page 27 and 28: Menu/Enter buttonUse to enter logge
Page 29 and 30: SensorMeasurementRangeAccuracyLogge
Page 31 and 32: 3.3.4. External PT-100 SensorConnec
Page 33 and 34: Normally Open will result in the al
Page 35 and 36: accepted by the DaqLink logger and
Page 37 and 38: First Time ChargingFrom a fully dra
Page 39 and 40: Note: The USB driver is installed a
Page 41 and 42: 3.8.2. Display ShutdownIf the logge
Page 43 and 44: Name and StatusAs explained previou
Page 45 and 46: established. In addition, if the lo
Page 47 and 48: Chapter 4:Using the DaqLinkSoftware
Page 49 and 50: Figure 14: Installing Silicon Labs
Page 51 and 52: stating that the device is ready fo
Page 53 and 54: 4.2.2. Viewing Sensor Data in MapVi
Page 55 and 56: In History View, the user may view
Page 57 and 58: • History view - Switches main wi
Page 59 and 60: •Logger is downloading data.Table
Page 61 and 62: ••Displayed graph functionHidde
Page 63 and 64:
4.4.3. Cancel DownloadWhen logger i
Page 65 and 66:
1. Click Tools > Define New Sensor
Page 67 and 68:
4.6. Tools > Options MenuItemsThe O
Page 69 and 70:
Path for application data filesThe
Page 71 and 72:
You must select the COM port which
Page 73 and 74:
4.7. Saving DataAs soon as a logger
Page 75 and 76:
Figure 28: Sync Data dialogThe data
Page 77 and 78:
4.9.1. Showing/Hiding the Data Sets
Page 79 and 80:
position you may then lock the Map
Page 81 and 82:
indicator so you can monitor the pr
Page 83 and 84:
Averaging PointsYou can choose have
Page 85 and 86:
CloseClicking Close will close the
Page 87 and 88:
Alarm DurationThe duration of the a
Page 89 and 90:
4.12.1. Contacts TabThe first step
Page 91 and 92:
Figure 33: Adding a group2. Enter a
Page 93 and 94:
4.12.4. Email and SMS NotificationF
Page 95 and 96:
the calibration settings it receive
Page 97 and 98:
Offset CalibrationTo calibrate the
Page 99 and 100:
Figure 35: Two-point calibration wi
Page 101 and 102:
3. You can repeat the procedure for
Page 103 and 104:
4.14.1. Using the Graph FeaturesThe
Page 105 and 106:
a different plot. For finer cursor
Page 107 and 108:
To select a data set to display on
Page 109 and 110:
4.14.2. Statistical AnalysisDaqLink
Page 111 and 112:
When printing a table, you can sele
Page 113 and 114:
Chapter 5:Updating DaqLinkSoftware
Page 115 and 116:
5. The files will be downloaded to
Page 117 and 118:
Once the file is downloaded the nex
Page 119 and 120:
A.2.DBSA710 and DBSA720OutputsAlarm
Page 121 and 122:
ContactRange: Open/CloseA.4.General
Page 123 and 124:
Appendix B:Safety InformationThe Da
Page 125 and 126:
Appendix C:Ordering InformationFor
Page 127 and 128:
Appendix D:Figures and TablesList o
Page 129:
120
show all

DaqLink User Guide - Contika

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?