309029D Automatic Delta Spray Air Spray Gun ... - Graco Inc.

More documents

Recommendations

Info

InstallationThe Delta Spray air spray guns were designed toproduce the highest quality finish with today’s fluids aswell as the Low V.O.C. (volatile organic compound)fluids of tomorrow.This spray gun can spray most coatings or finishescurrently being used for automotive, industrial, aerospace,marine, wood, plastic and architectural applications,while easily operating from paint delivery systemssuch as pressure pots or remote pumps forproduction line operation.The air regulator must have a minimum air flowcapacity of 30 scfm at 100 psi (0.7 MPa, 7 bar) airpressure.Ventilate the Spray BoothWARNINGTo prevent hazardous concentrations oftoxic and/or flammable vapors, sprayonly in a properly ventilated spray booth.Do not operate the spray gun unlessventilation fans are operating.In a circulating system, apply anti-seize lubricant222955 to the threads and mating faces of the manifold(101) and the elbows (107), supplied unassembled.Install the elbows (107) in both fluid ports ofthe manifold (101). Connect the fluid supply line to oneelbow and the fluid return line to the other. The manifoldfluid ports are reversible.In a non-circulating system, apply anti-seize lubricant222955 to the threads and mating faces of the manifold(101), a plug (109), and an elbow (107), suppliedunassembled. Install an elbow (107) in one fluid port ofthe manifold (101), and a plug (109) in the other port.Install the internal plug (5) in the gun fluid port on thesame side as the manifold plug. Connect the fluidsupply line to the manifold elbow (107). See Fig. 1.Non–Circulating Setup Shown (cutaway view)12Remove when used in circulating systemsReplace with an elbow (107) when used in circulating systemsCheck and follow all of the National,State and Local codes regarding air exhaustvelocity requirements.Check and follow all local safety and fire codes.1 52 109101107Configure the Gun and ManifoldThe gun is supplied with an internal fluid plug (5). SeeFig. 1. To use the gun in a circulating system, removethe internal plug. In a non-circulating system, leave theplug in place to minimize flush time.Fig. 1Install the gun on the manifold, using the four screws.Thread the screws by hand, then torque alternatelyand evenly to 65 in-lb (7.3 Nm).6 309029
InstallationMount the GunTo mount the gun on a reciprocating arm [0.5 in. (13mm) diameter maximum], insert the bar (A) throughthe hole in the manifold as shown in Fig. 2. Secure thegun to the bar by tightening the mounting screw (B).The tip of the gun should be 8 to 10 in. (200 to 250mm) from the surface of the object being sprayed.KEYA Mounting BarB Mounting Screw (onbottom of manifold)To mount the gun on a stationary support, see Fig. 3.Also refer to the Mounting Hole Layout on page 29.Attach the gun to the support with two M5 x 0.8capscrews (C). The screws must be long enough toengage the threaded holes in the gun manifold to adepth of 1/4 in. (6 mm). The tip of the gun should be 8to 10 in. (200 to 250 mm) from the surface of theobject being sprayed.KEYC M5 x 0.8 CapscrewsCAFig. 3BFig. 2309029 7
Page 2 and 3: SymbolsWarning SymbolWARNINGThis sy
Page 4 and 5: TERMS:Light Fluid:Medium Fluid:Sele
Page 8 and 9: Setup1. Connect the Air LineNOTE: Y
Page 10 and 11: Setup6. Adjust the Spray PatternWAR
Page 12 and 13: 12 309029Notes
Page 14 and 15: Daily Gun Care, Flushing, and Clean
Page 16 and 17: TroubleshootingWARNINGPRESSURIZED E
Page 18 and 19: 18 309029Notes
Page 20 and 21: ServiceItems Needed for Service1/16
Page 22 and 23: ServiceReassembly1. Non-circulating
Page 24 and 25: PartsPart No. 241737 to 241744, Ser
Page 26 and 27: Part No. 241696, Series AManifold w
Page 28 and 29: AccessoriesFluid Whip Hose Assembly
Page 30 and 31: Technical DataMaximum working fluid
Page 32: Graco Standard WarrantyGraco warran

309029D Automatic Delta Spray Air Spray Gun ... - Graco Inc.

Create successful ePaper yourself

Delete template?

Save as template?