welder level c program outline - Industry Training Authority

More documents

Recommendations

Info

5. Perform guided cuts on lowcarbon steel plate and sheet.6. Wash nuts off bolts and gougeweldments.Guided cuts on low carbon steel plateand sheet - refer to practicalcompetency for procedureGuided circular cuts on low carbon steelplate - refer to practical competency forprocedureWash nuts off bolts - refer to practicalcompetency for procedureGouge weldments - refer to practicalcompetency for procedure7. Perform freehand cuts on mildsteel pipe. Straight cuts on low carbon steel pipe -refer to practical competency forprocedure Bevel cuts on low carbon steel pipe -refer to practical competency forprocedureNOTE: Refer To Current Welder Training Program Curriculum Module/Line P2-4.Achievement Criteria:The learner will be evaluated on the ability to perform freehand and guided cuts on lowcarbon steel plate, sheet round stock, structural shapes and pipes as part of a practicalshop project as per the acceptance criteria in the current curriculum module/line P2-4..Welder Level C Program Outline • Industry Training Authority 35
LINE B:PERFORMS OXY-FUEL CUTTING PROCESSES (OFC)Competency: B-4 Perform Cuts with Cutting Machines, Automatic andSemi-AutomaticLearning Objectives:The learner will be able to set up and operate a variety of cutting machines and producehigh quality straight and bevel cuts safely.LEARNING TASKS1. Performs cuts with a straight-linecutting machine using oxy-fuelgas.2. Perform cuts with a shape-cuttingmachine using oxy-fuel gas.CONTENT Refer to practical competency forprocedureRefer to practical competency forprocedure3. Perform cuts with a pipe-bevelingmachine using oxy-fuel gas.Refer to practical competency forprocedureNOTE: Refer To Current Welder Training Program Curriculum Module/Line P2-5.Achievement Criteria:The learner will be evaluated on the ability to perform cuts with cutting machines,automatic and semi-automatic as part of a practical shop project as per the acceptancecriteria in current curriculum module/line P2-5.Welder Level C Program Outline • Industry Training Authority 36
Page 4 and 5: ACKNOWLEDGEMENTSThe Program Outline
Page 6: SECTION 1OCCUPATION ANALYSIS CHARTW
Page 13 and 14: TheoryPracticalLine DPerforms Shiel
Page 15 and 16: Theory PracticalI-5 Describe Hoisti
Page 17 and 18: LINE A:APPLIES OCCUPATIONAL SKILLSC
Page 33 and 34: LINE A:Competency:APPLIES OCCUPATIO
Page 35 and 36: NOTE: Refer To Current Welder Train
Page 37 and 38: 5. Describe cutting torches, cuttin
Page 39: LINE B:PERFORMS OXY-FUEL CUTTING PR
Page 43 and 44: LINE C:PERFORMS FUSION AND BRAZE WE
Page 53 and 54: LINE C:Competency:PERFORMS FUSION A
Page 55 and 56: 2. Describe safety requirements,pre
Page 57 and 58: 5. Describe and select electrodehol
Page 59 and 60: 4. Describe correct handling andsto
Page 61 and 62: LINE D:PERFORMS SHIELDED METAL ARC
Page 67 and 68: 2. Demonstrate the build-up andhard
Page 69 and 70: LINE D:Competency:PERFORMS SHIELDED
Page 71 and 72: 3. Weld groove welds in the flat(1G
Page 73 and 74: 6. Describe safety requirements. P
Page 75 and 76: 4. Describe procedures for gougingc
Page 77 and 78: 4. Describe the main factors ofPAC.
Page 79 and 80: Welding gunToxic fumes/ventilationO
Page 81 and 82: 4. Describe equipment for semiautom
Page 83 and 84: LINE F:PERFORMS SEMI-AUTOMATIC WELD
Page 85 and 86: LINE F:P)(FCAW)PERFORMS SEMI-AUTOMA
Page 91 and 92:
4. Weld fillet welds in the horizon
Page 93 and 94:
LINE F:P)(FCAW)Competency:PERFORMS
Page 95 and 96:
Page 97 and 98:
LINE F:Competency:PERFORMS SEMI-AUT
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Achievement Criteria:The learner wi
Page 109 and 110:
Page 111 and 112:
LINE G:DESCRIBE BASIC METALLURGY RE
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
LINE I:DESCRIBES AND PERFORMS MATEI
Page 121 and 122:
4. Recognize and name commonknots,
Page 123 and 124:
4. Identify common rigginghardware.
Page 125 and 126:
LINE I:DESCRIBES AND PERFORMS MATER
Page 127 and 128:
LINE J:READS WELDING DRAWINGSCompet
Page 129 and 130:
LINE J:READS WELDING DRAWINGSCompet
Page 131 and 132:
4. Identify the dimensioning ofbolt
Page 133 and 134:
3. Identify bills of material and o
Page 135 and 136:
LINE K:LAYOUT AND FABRICATE COMPONE
Page 137 and 138:
LINE K:LAYOUT AND FABRICATE COMPONE
Page 139 and 140:
LINE N:PERFORMS SUBMERGED ARC WELDI
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
INSTRUCTORSWELDER C TRAINING PROVID
Page 147 and 148:
STUDENT FACILITIES‣ Adequate lunc
Page 149 and 150:
Testing EquipmentAdapter fittingsAm
Page 151 and 152:
RECOMMENDED REFERENCETEXTBOOKSWELDE
Page 153 and 154:
APPENDIX ONEWELDER LEVEL CFINAL WEL
Page 155 and 156:
Welder Level C Apprenticeship Progr
Page 159 and 160:
APPENDIX TWOWELDER LEVEL CPROGRAMFI
Page 161 and 162:
Welder Level C Program Outline •
Page 165 and 166:
Page 167 and 168:
Page 169:
FINAL PRACTICAL EXAMINATION #3MATER
Page 173 and 174:
Level "C" Weld Test #1 Performance
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Level C Final Weld TestsPRS-CWelder
Page 181 and 182:
In addition to the above requiremen
show all

welder level c program outline - Industry Training Authority

Create successful ePaper yourself

Delete template?

Save as template?