welder level c program outline - Industry Training Authority

More documents

Recommendations

Info

LINE C:PERFORMS FUSION AND BRAZE WELDING USINGOXY-FUEL PROCESSES (OFW)Competency: C-7 Fusion Weld Square Groove Welds on Low Carbon SteelSheetLearning Objectives:The learner will fusion weld groove welds on low carbon steel sheet using OFWprocesses.LEARNING TASKS1. Fusion weld groove welds in theflat (1G) position on low carbonsteel sheet.CONTENT Refer to practical competency for WeldProcedure Specification (WPS)NOTE: Refer To Current Welder Training Program Curriculum Module/Line P3-5.Achievement Criteria:The learner will be evaluated on the ability to fusion weld groove welds on low carbonsteel sheet using OFW processes as part of a practical shop project as per theacceptance criteria in the current curriculum module/line P3-5; evaluation must meetCSA W59 standards for cyclically loaded structures.Welder Level C Program Outline • Industry Training Authority 45
LINE C:PERFORMS FUSION AND BRAZE WELDING USINGOXY-FUEL PROCESSES (OFW)Competency: C-8 Braze Weld Fillet Welds on Low Carbon Steel SheetLearning Objectives:The learner will braze weld fillet welds on low carbon steel sheet using OFW processes.LEARNING TASKS1. Describe the procedures forbraze welding low carbon steel.CONTENT Pre-leaning and edge preparation Flame setting Filler rods and flux Number of passes Determining the quality of work2. Braze weld fillet welds in the flat(1F) and horizontal (2F) positionson lap and tee joints on lowcarbon steel sheet.Braze weld on lap joint in the 2Fposition - refer to practical competencyfor Weld Procedure Specification(WPS)Braze weld on tee joint in the 1Fposition - refer to practical competencyfor Weld Procedure Specification(WPS)NOTE: Refer To Current Welder Training Program Curriculum Module/Line P3-7.Achievement Criteria:The learner will be evaluated on the ability to braze weld fillet welds on low carbon steelsheet using OFW processes as part of a practical shop project as per the acceptancecriteria the current curriculum module/line P3-7; evaluation must meet CSA W59standards for cyclically loaded structures.Welder Level C Program Outline • Industry Training Authority 46
Page 4 and 5: ACKNOWLEDGEMENTSThe Program Outline
Page 6: SECTION 1OCCUPATION ANALYSIS CHARTW
Page 13 and 14: TheoryPracticalLine DPerforms Shiel
Page 15 and 16: Theory PracticalI-5 Describe Hoisti
Page 17 and 18: LINE A:APPLIES OCCUPATIONAL SKILLSC
Page 33 and 34: LINE A:Competency:APPLIES OCCUPATIO
Page 35 and 36: NOTE: Refer To Current Welder Train
Page 37 and 38: 5. Describe cutting torches, cuttin
Page 39 and 40: LINE B:PERFORMS OXY-FUEL CUTTING PR
Page 41 and 42: LINE B:PERFORMS OXY-FUEL CUTTING PR
Page 43 and 44: LINE C:PERFORMS FUSION AND BRAZE WE
Page 49: LINE C:PERFORMS FUSION AND BRAZE WE
Page 53 and 54: LINE C:Competency:PERFORMS FUSION A
Page 55 and 56: 2. Describe safety requirements,pre
Page 57 and 58: 5. Describe and select electrodehol
Page 59 and 60: 4. Describe correct handling andsto
Page 61 and 62: LINE D:PERFORMS SHIELDED METAL ARC
Page 67 and 68: 2. Demonstrate the build-up andhard
Page 69 and 70: LINE D:Competency:PERFORMS SHIELDED
Page 71 and 72: 3. Weld groove welds in the flat(1G
Page 73 and 74: 6. Describe safety requirements. P
Page 75 and 76: 4. Describe procedures for gougingc
Page 77 and 78: 4. Describe the main factors ofPAC.
Page 79 and 80: Welding gunToxic fumes/ventilationO
Page 81 and 82: 4. Describe equipment for semiautom
Page 83 and 84: LINE F:PERFORMS SEMI-AUTOMATIC WELD
Page 85 and 86: LINE F:P)(FCAW)PERFORMS SEMI-AUTOMA
Page 91 and 92: 4. Weld fillet welds in the horizon
Page 93 and 94: LINE F:P)(FCAW)Competency:PERFORMS
Page 97 and 98: LINE F:Competency:PERFORMS SEMI-AUT
Page 101 and 102:
LINE F:Competency:PERFORMS SEMI-AUT
Page 103 and 104:
LINE F:Competency:PERFORMS SEMI-AUT
Page 105 and 106:
LINE F:P)(FCAW)Competency:PERFORMS
Page 107 and 108:
Achievement Criteria:The learner wi
Page 109 and 110:
LINE F:P)(FCAW)Competency:PERFORMS
Page 111 and 112:
LINE G:DESCRIBE BASIC METALLURGY RE
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
LINE I:DESCRIBES AND PERFORMS MATEI
Page 121 and 122:
4. Recognize and name commonknots,
Page 123 and 124:
4. Identify common rigginghardware.
Page 125 and 126:
LINE I:DESCRIBES AND PERFORMS MATER
Page 127 and 128:
LINE J:READS WELDING DRAWINGSCompet
Page 129 and 130:
LINE J:READS WELDING DRAWINGSCompet
Page 131 and 132:
4. Identify the dimensioning ofbolt
Page 133 and 134:
3. Identify bills of material and o
Page 135 and 136:
LINE K:LAYOUT AND FABRICATE COMPONE
Page 137 and 138:
LINE K:LAYOUT AND FABRICATE COMPONE
Page 139 and 140:
LINE N:PERFORMS SUBMERGED ARC WELDI
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
INSTRUCTORSWELDER C TRAINING PROVID
Page 147 and 148:
STUDENT FACILITIES‣ Adequate lunc
Page 149 and 150:
Testing EquipmentAdapter fittingsAm
Page 151 and 152:
RECOMMENDED REFERENCETEXTBOOKSWELDE
Page 153 and 154:
APPENDIX ONEWELDER LEVEL CFINAL WEL
Page 155 and 156:
Welder Level C Apprenticeship Progr
Page 159 and 160:
APPENDIX TWOWELDER LEVEL CPROGRAMFI
Page 161 and 162:
Welder Level C Program Outline •
Page 165 and 166:
Page 167 and 168:
Page 169:
FINAL PRACTICAL EXAMINATION #3MATER
Page 173 and 174:
Level "C" Weld Test #1 Performance
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Level C Final Weld TestsPRS-CWelder
Page 181 and 182:
In addition to the above requiremen
show all

welder level c program outline - Industry Training Authority

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?