7. operating the flexipress - Grass

More documents

Recommendations

Info

3-001 Dust and Noise Emission Values 12 3. DESCRIPTION OF PRODUCTS Noise Measuring Conditions The Lpa workplace-based emission value pursuant to prEN 31202 as amended by CEN-TC 142 to achieve an accuracy class of better than 3 dB When idling = -------- dB(A) When drilling = 77.8 dB(A) Measuring uncertainty constant K equals 4.0 dB/A Machine setup during the measuring operation: Drill bits: 1 hinge cup drill bit dia. 35 mm t = 13 mm n = 2890 rpm 2 dowel drill bits dia. 8 mm t = 13 mm n = 2940 rpm Workpiece: uncoated particle board Microphone position: 1 m in front of drill motor axle at a height of 1.5 m Dust: Dust emission value pursuant to DIN 33893 Part 2 Statistically proven maximum value ....... mg/m 3 Specifications for exhaust connection: Suction exhaust pipe dia. 100 mm Mean air speed 20 m/sec Static suction 920 Pa Connection to an exhaust system The Flexipress must be connected to a vacuum suction system which complies with the specifications given above. The connecting lines must be flame-resistant. If an electrical coupling is required for the vacuum suction system, a volumetric flow monitor is available from Grass GmbH as a special accessory. This is connected at the position shown on the wiring diagram in section 4-007. Collection elements The dust and shavings collection elements of the Flexipress are designed to ensure that, when used correctly, the amount of wood dust falls below the TRK requirements. (Connection to an exhaust system which meets the specifications given above; test reports on dust measurements pursuant to DIN 33893, Part 2 performed by an independent institution are available on request). The star in your cabinet
3-002 Applications The Flexipress drilling and insertion machine is designed exclusively for the operations described in sections 7-6 and 7-7 “Application Examples”. The manufacturer guarantees smooth, trouble-free operation for these applications. Misuse or failure to adhere to the manufacturer’s recommendations may result in injury to operating personnel or damage to equipment or workpieces. 3-003 Equipment Identification All machines are provided with a nameplate stating the year of manufacture, the serial number, machine model, connecting voltage and frequency plus the required pressure for compressed air connections. The motor frame also bears a label stating the machine designation. 3-004 Basic Equipment 3. DESCRIPTION OF PRODUCTS The Flexipress is supplied completely fitted and consists of the following parts: - Sturdy base frame with guide bars for the horizontal drilling head plus hand wheel to adjust the vertical drilling setup distance (table adjustment) - Sturdy machine frame with vertical motor support with electric motor, pneumatic feed, adjustable drilling depth stop for the drilling head - Insertion die arm to take insertion dies and hold-down plate for horizontal drilling - Complete electrical equipment with thermal overload protection and lockable switch, 3 m of feeder cable with 5-pole CEE 5x16 A plug - Complete pneumatic control, including maintenance unit with adjustable feed and operating speed, 3m of compressed air feeder hose with quick-release coupling - Connection for the dust removal system - Detailed operating manual - Tool set comprising 8/10 mm and 13/17 mm fork wrenches, 1 each Allen keys 2/2.5/3/4/5/6 mm, one marking gauge for hinges plus one stop setting gauge L=600 The star in your cabinet 13
Page 1 and 2: OPERATING INSTRUCTIONS Grass Flexip
Page 3 and 4: Weights Total weight of Flexipress
Page 5 and 6: TABLE OF CONTENTS Page 7. Operating
Page 7 and 8: 1-001 List of Figures LIST OF FIGUR
Page 9 and 10: 2-001 Safety Information - It is th
Page 11: 2-006 Potential Hazards and Suitabl
Page 15 and 16: 3. DESCRIPTION OF PRODUCTS Side sto
Page 17 and 18: 3. DESCRIPTION OF PRODUCTS Designat
Page 19 and 20: 4. DESCRIPTION OF MACHINE COMPONENT
Page 41 and 42: 6-001 Pneumatic Connection The Flex
Page 43 and 44: 7-1 Requirements for the Operators
Page 45 and 46: 7-301 Setting the Vertical Drilling
Page 47 and 48: 7-303 Setting the Vertical Drilling
Page 49 and 50: 7. OPERATING THE FLEXIPRESS 7-401 S
Page 51 and 52: 7-501 Setting the Side Stops Fig. 7
Page 53 and 54: 7-503 Using the Index Gauge When Dr
Page 55 and 56: 7-601 Drilling and Inserting Grass
Page 57 and 58: 7-602 Drilling and Inserting Grass
Page 59 and 60: 7-603 Drilling Lines of Holes Figs
Page 61 and 62: 7-604 Drilling Fronts for Grass Zar
Page 63 and 64:
7-605 Drilling Back Panels for Gras
Page 65 and 66:
7-606 Drilling and Inserting Visibl
Page 67 and 68:
7-607 Bohren und Einpressen von Ver
Page 69 and 70:
7-608 Drilling Holes for Handles Fi
Page 71 and 72:
7-609 Drilling Vertical Holes for D
Page 73 and 74:
7-610 Drilling Holes for Fastening
Page 75 and 76:
7-701 Drilling Horizontal Holes for
Page 77 and 78:
7-702 Drilling Horizontal Holes for
Page 79 and 80:
7-703 Drilling Holes for Joint Supp
Page 81 and 82:
7. OPERATING THE FLEXIPRESS 7-801 D
Page 83 and 84:
8. TROUBLE SHOOTING AND PROBLEM SOL
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
10-001 Guarantee Certificate Purcha
Page 99 and 100:
10-002 Disposal Form Purchaser: Nam
Page 101 and 102:
10-003 Resale Form Vendor: Name: .
Page 103 and 104:
10-004 Questionnaire 1 - Reason for
Page 105 and 106:
10-005 Questionnaire 2 - Satisfacti
Page 107 and 108:
The star in your cabinet NOTES 107
Page 109 and 110:
REPRESENTATIVES AROUND THE WORLD MD
show all

7. operating the flexipress - Grass

Create successful ePaper yourself

Delete template?

Save as template?