7. operating the flexipress - Grass

More documents

Recommendations

Info

8. TROUBLE SHOOTING AND PROBLEM SOLVING Fig. 8-101-01 Fig. 8-102-01 82 � � � � � The star in your cabinet
8. TROUBLE SHOOTING AND PROBLEM SOLVING 8-101 The Vertical Drilling Setup Distance is not Correct - Adjusting the Digital Position Indicator Fig. 8-101-01 Tools required: Allen key 2 mm Precise measuring device such as calliper gauge - Turn off the main switch - Lift up the front gearbox cover. - Remove all quick-change chucks incl. drill bits from the gearbox, see section 7-202 - Fasten a drill bit in the zero position of the line drilling spindles - See Fig. 7-401-01 for gearbox configuration - Turn the main switch back on - Place a test piece on the machine table and press it against the stop pins on the fence - With the other hand, press the vertical drilling head start button until the drilling depth set with knurled screw “6” on Fig. 4-002-03 is reached. - Measure the drilling setup distance on the test piece and compare with the value set on digital position indicator “1” - If the two values are not the same: - Loosen set screw “2” with 2 mm Allen key and turn stop ring “3” until the value indicated is the same as the measured value. Tighten the set screw - Test drill again and check. - Repeat the adjustment operation until the two values are the same 8-102 The Vertical Drilling Depth is not Correct - Adjusting the Digital Position Indicator Fig. 8-102-01 Tools required: Allen key 2 mm Precise measuring device such as calliper gauge - Turn off the main switch - Lift up the front gearbox cover. - Remove all quick-change chucks incl. drill bits from the gearbox, see section 7-202 - Fasten a drill bit to the zero position of the line drilling spindles - See Fig. 7-401-01 for gearbox placement - Turn the main switch back on - Place a test piece on the machine table and press it against the stop pins on the fence - Set the material thickness of the test piece, see section 7-301 - With the other hand, press the vertical drilling head start button until the drilling depth set with knurled screw “6” on Fig. 4-002-03 has been reached. - Measure the drilling depth on the test piece. It should be 13 mm. - If the value measured is not 13 mm, loosen set screw “1” on Fig. 8-002-01 and turn ring “2” on the digital position indicator until the following new value is shown. Retighten set screw “1” New value = “material thickness of test piece“ minus “measured drilling depth” plus “13” (required drilling depth = standard setting) - Test drill again and measure. Repeat until the value measured is 13 mm. Caution: While the machine is being operated: keep hands clear of the danger zone around the hold-down devices, the insertion die arm and the gearbox. The safety information given in section 2 is to be followed whenever the machine is being operated. The star in your cabinet 83
Page 1 and 2:
OPERATING INSTRUCTIONS Grass Flexip
Page 3 and 4:
Weights Total weight of Flexipress
Page 5 and 6:
TABLE OF CONTENTS Page 7. Operating
Page 7 and 8:
1-001 List of Figures LIST OF FIGUR
Page 9 and 10:
2-001 Safety Information - It is th
Page 11 and 12:
2-006 Potential Hazards and Suitabl
Page 13 and 14:
3-002 Applications The Flexipress d
Page 15 and 16:
3. DESCRIPTION OF PRODUCTS Side sto
Page 17 and 18:
3. DESCRIPTION OF PRODUCTS Designat
Page 19 and 20:
4. DESCRIPTION OF MACHINE COMPONENT
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32: 4. DESCRIPTION OF MACHINE COMPONENT
Page 41 and 42: 6-001 Pneumatic Connection The Flex
Page 43 and 44: 7-1 Requirements for the Operators
Page 45 and 46: 7-301 Setting the Vertical Drilling
Page 47 and 48: 7-303 Setting the Vertical Drilling
Page 49 and 50: 7. OPERATING THE FLEXIPRESS 7-401 S
Page 51 and 52: 7-501 Setting the Side Stops Fig. 7
Page 53 and 54: 7-503 Using the Index Gauge When Dr
Page 55 and 56: 7-601 Drilling and Inserting Grass
Page 57 and 58: 7-602 Drilling and Inserting Grass
Page 59 and 60: 7-603 Drilling Lines of Holes Figs
Page 61 and 62: 7-604 Drilling Fronts for Grass Zar
Page 63 and 64: 7-605 Drilling Back Panels for Gras
Page 65 and 66: 7-606 Drilling and Inserting Visibl
Page 67 and 68: 7-607 Bohren und Einpressen von Ver
Page 69 and 70: 7-608 Drilling Holes for Handles Fi
Page 71 and 72: 7-609 Drilling Vertical Holes for D
Page 73 and 74: 7-610 Drilling Holes for Fastening
Page 75 and 76: 7-701 Drilling Horizontal Holes for
Page 77 and 78: 7-702 Drilling Horizontal Holes for
Page 79 and 80: 7-703 Drilling Holes for Joint Supp
Page 81: 7. OPERATING THE FLEXIPRESS 7-801 D
Page 85 and 86: 8. TROUBLE SHOOTING AND PROBLEM SOL
Page 97 and 98: 10-001 Guarantee Certificate Purcha
Page 99 and 100: 10-002 Disposal Form Purchaser: Nam
Page 101 and 102: 10-003 Resale Form Vendor: Name: .
Page 103 and 104: 10-004 Questionnaire 1 - Reason for
Page 105 and 106: 10-005 Questionnaire 2 - Satisfacti
Page 107 and 108: The star in your cabinet NOTES 107
Page 109 and 110: REPRESENTATIVES AROUND THE WORLD MD
show all

7. operating the flexipress - Grass

Create successful ePaper yourself

Delete template?

Save as template?