Rugby 100LR User Manual - Opti-cal Survey Equipment

More documents

Recommendations

Info

To Enter Calibration Mode:1 With the power off, press the PowerButton once to turn on power.2 Press and hold the Up and DownArrow Buttons. While holding thesebuttons, press and release thepower button. Then, release thearrow buttons.3 The Rugby is now in calibrationmode. The low battery indicator willblink at 5 Hz and the out of levelindicator will blink at 1 Hzalternately to confirm that the unit isin calibration mode for Axis One.Rugby100LR-10 Cal Mode 5 to 1.tifDo not push the arrowbuttons unless you plan to changecalibration! To exit this mode, pressthe power button once. The unit willpower off without making any changes.4 Align the unit so that you are facingthe control panel and looking overthe top of the unit to the calibrationmarks on the wall. This is Axis One(position 1).Axis One (1-2)Axis Two (3-4)3Rugby100LR-11 Rugby top view1.eps5 Use the Up or Down Arrow Buttonsto raise or lower the beam to thedesired elevation for levelcalibration in position 1. When thearrow button is pressed, the toplaser emission indicator LED willturn off for one half second toindicate that a key has beenpressed.6 Rotate the laser 180° and check theopposite side of Axis One(position 2).7 Reposition the Rugby so that thehandle is now pointing at thecalibration marks on the wall. Thisis Axis Two (position 3).8 Press the Auto/Manual Button toenter the calibration mode for thesecond axis. The low battery andout of level indicators will nowreverse their blink modes to confirmthe Rugby is now in calibrationmode for Axis Two.9 Use the Up or Down Arrow Buttonsto raise or lower the beam to thedesired elevation for levelcalibration in Axis Two (position 3).When the arrow button is pressed,the top, laser emission indicatorLED will turn off for one half secondto indicate that a key has beenpressed.10 Rotate the laser 180° and check theopposite side of Axis Two(position 4).11 Once the desired calibration hasbeen set for both axes, press thePower Button once to store theinformation and turn the power off.The Rugby will be set to the newcalibration when power is reapplied.Rugby 100 LR-2.2.1en16 Calibration
TroubleshootingSymptomThe Rugby 100LR doesnot turn on.The Rugby 100LR doesnot turn off.The Rugby 100LR isworking, but it does notself-level.The Rugby 100LRcontinues to level inmanual mode.Possible Causes and SolutionsThe battery charge is low or dead.• If the Rugby 100LR has alkaline batteries,remove the battery pack from the base of theRugby and replace all four batteries with fresh D-cell alkaline batteries.• If the Rugby 100LR has a rechargeable) NiMHbatterypack, plug the battery charger into theRugby's charge jack and then connect it to astandard electrical outlet. Always plug the batterycharger into the Rugby's charge jack first andthen plug it into the electrical outlet, otherwise theRugby's charge jack might emit sparks.The Off/On Power Button is used also to changethe speed of the rotating head.• Press once to turn the Rugby on at 5 rps. Press asecond time to increase the speed of the rotatinghead to 10 rps. Press a third time to turn the unit off.The Rugby 100LR must be in automatic mode toself-level.• In automatic the emission indicator will blink untilthe laser has completed self-leveling.• In manual mode with cross axis self-leveling theManual Mode Indicator will flash at 5 Hz and onlythe cross axis will self-level.• In full manual mode leveling the Manual ModeIndicator will flash slowly at 1 Hz and the Rugbywill not self-level.The Rugby 100LR has two manual modes.• In manual mode with cross axis self-leveling theManual Mode Indicator will flash at 5 Hz and thecross axis will self-level.Troubleshooting17 Rugby 100 LR-2.2.1en
Page 5 and 6: Generalized Boltzmann Physical Kine
Page 7 and 8: • Pressing the arrow buttons will
Page 9 and 10: Basic operationAutomatic Operation
Page 11 and 12: NiMH Battery PackGeneral Informatio
Page 13 and 14: Technical DataRugby 100LROperating
Page 15: CalibrationThe Rugby is calibrated
Page 19 and 20: Care and TransportTransportWhen dis
Page 21 and 22: ResponsibilitiesResponsibility for
Page 23 and 24: WARNING:If the product is improperl
Page 25 and 26: ElectromagneticCompatibility (EMC)T
Page 27 and 28: Safety Directions27 Rugby 100 LR-2.

Rugby 100LR User Manual - Opti-cal Survey Equipment

Create successful ePaper yourself

Delete template?

Save as template?