INFOBALE - Hjallerup Maskinforretning A/S

More documents

Recommendations

Info

EN2.3) Function menuThe function menu can be called up from theworking screen by simultaneously pressing and. Settings can be changed using the andkeys.= select or increase value.= select or decrease value.(F1) F+ menuConfirm the selected F+ menu.(F2) Trip bale counter.Reset by simultaneously pressing and .(F3) Total number of bales produced by themachine. Not resettable.(F4) Display contrastAdjust the displayed contrast(35 – 99%)(F5) Sound levelAdjust the sound level(0 – 100%)(F6) Language settingsAvailable settings are: EN, NL, FR, DE, ES, IT.(F7) FanKnotter cleaning using fans (option) can beswitched on or off.(F8) Knotter cleaningKnotter cleaning using a compressor (option)can be switched on or off.(F9) Automatic oil lubricating systemThe automatic oil lubricating system (option)can be switched on or off.(F10) Automatic grease lubricating systemThe automatic grease lubricating system(option) can be switched on or off.(F11) Automatic knife cleaningAutomatic knife cleaning system (onlyapplicable for Opticut) can be switched on oroff.(F12) Last F+ screensimultaneously = set value to default settingor 0.= scroll key —> to next screenPressing this key also confirms the setting of thecurrent screen before the next screen appears.F1F2F3F4F5F6F7F8F9F10F11F126© Kverneland
EN3) Baling processCaution: it is vital to let the machine run at nominalspeed during use. Only then can flawless operationof the various functions be guaranteed.The forward speed (choice of gear) must always beadapted to the swath width. To achieve maximumbale density, the separate wads in the bale must notbe thicker than 5 cm. If large quantities regularlycause feeder overload, then the forward speed mustbe reduced.Adapt the forward speed to the number ofcompression strokes per bale. The working screenshowing the plunger strokes per bale is a good toolhere.Examples:Bale growth per plunger stroke can be estimated onthe basis of the compression time per bale. theplunger makes 45 compression strokes/min at1000 rpm. Allow for turning at the headland andstopping in the field.bale length(in cm) 80 120 160 180 200 220 240 250 260no strokes per bale 16 24 32 36 40 44 48 50 523.1) Setting the hydraulic densitypressureThe operator has to set the hydraulic densitypressure.= increase pressure= decrease pressureAdapt the density pressure to the conditions(material, crop humidity, swath shape, twinestrength etc.).Caution: The maximum density pressure is 170 bar.Let the pto run so the hydraulic pressure can beread from the pressure gauge.© Kverneland7
Page 1 and 2: Operation manualINFOBALE+-G0203GPR(
Page 3 and 4: This operation manual contains the
Page 5 and 6: EN1.2) Building inMount the INFOBAL
Page 7: EN2) Working with the high density
Page 11 and 12: EN4) Fault messagesCaution: When th
Page 13 and 14: EN5) Electric emergency control den
Page 15 and 16: EN7) Factory FunctionsSimultaneousl
Page 17 and 18: EN• ML- max. setting • 500 = gr
Page 19 and 20: EN- Needle frame shear bolt sensor-
Page 21 and 22: EN© Kverneland19
Page 23 and 24: EN10) Trouble shooting tableCaution
Page 25: KVERNELAND GELDROP BVNuenenseweg 16

INFOBALE - Hjallerup Maskinforretning A/S

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?