Configuration Manual Synchronous Motors 1FK7 - Siemens ...

More documents

Recommendations

Info

Gearbox Planetary gearbox 5.3.2.4 Selection and ordering data, single-stage planetary gearbox, series SP+ Motor Natural cooling Planetary gearbox single-stage Type Type Rotary play Gearboxweight approx. Available gear ratio i = 4 5 7 10 n G1 Max. permissible motor speed S3-60% Max. perm. output torque S3-60% Max. perm. radial output shaft load 1) Max. perm. axial output shaft load 1) 1FK7 Synchronous Motors 5-38 Configuration Manual (PFK7), 10/2005 Edition, 6SN1197-0AD06-0BP1 (n 1) M G2 (T 2B) F r (F 2Rmax) arcmin kg rpm Nm N N 1FK7022 SP 060S-MF1 ≤ 4 1.9 4 4 4 4 6000 40 2700 2400 1FK7032 4 4 4 4 (32 for i = 10) 1FK7033 4 4 4 4 1FK7040 SP 075S-MF1 ≤ 4 3.9 4 4 4 4 6000 110 4000 3350 1FK7042 4 4 4 4 (90 for i = 10) 1FK7043 4 4 4 4 1FK7044 4 4 4 4 1FK7060 SP 100S-MF1 ≤ 3 7.7 4 4 4 4 4500 300 6300 5650 1FK7061 4 4 4 4 (225 for i = 10) 1FK7063 4 4 4 4 1FK7064 4 4 4 4 1FK7080 SP 140S-MF1 ≤ 3 17.2 4 4 4 4 4000 600 9450 9870 1FK7082 4 4 4 4 (480 for i = 10) 1FK7083 4 4 4 4 1FK7085 4 4 4 4 1FK7100 SP 180S-MF1 ≤ 3 34 4 4 4 4 3500 1100 14700 14150 1FK7101 4 4 4 4 1FK7103 4 4 4 4 1FK7105 4 4 4 – 1FK7105 SP 210-MF1 2) ≤ 4 53 – – – 4 2200 2720 18000 22500 Order codes Gearbox shaft with key J02 J03 J05 J09 Gearbox shaft without key J22 J23 J25 J29 Ordering data 1FK7...-.A.71-..7 5-Z Order No. of the motor with identifier "-Z" and J7 7 G H order code for mounting the planetary gearbox assigned to the motor Prerequisite for mounting planetary gearboxes: Plain motor shaft end IP65 degree of protection, anthracite paint finish F a (F 2Amax) 1) Referred to the center of the drive shaft. 2) For this version, the oil quantity depends on the mounting position. In the case of a vertical mounting position, the 12th position in the Order No. should be "9" and a further order code also has to be specified: 1FT6...-.A.79-.. 7 5-Z J.. + M1 7 G H mounting position IM V1 H G mounting position IM V3
5.3.2.5 Technical data, single-stage planetary gearbox, SP+ series Gearbox Planetary gearbox Planetary gearbox with 1FK7 motor, natural cooling Single-stage Gearratio Motor speed Output Moment of inertia of gearboxs (referred to the drive) Type torque Continuous duty S1 1) 1FK702. 1FK703. 1FK704. 1FK706. 1FK708. 1FK710. nN1 MN2 (T2N ) J1 J1 J1 J1 J1 J1 rpm Nm kgcm2 kgcm2 kgcm2 kgcm2 kgcm2 kgcm2 SP 060S-MF1 4 3300 26 0.16 0.24 – – – – 5 3300 26 0.13 0.22 – – – – 7 4000 26 0.11 0.19 – – – – 10 4000 17 0.10 0.18 – – – – SP 075S-MF1 4 2900 75 – – 0.94 – – – 5 2900 75 – – 0.83 – – – 7 3100 75 – – 0.73 – – – 10 3100 52 – – 0.67 – – – SP 100S-MF1 4 2500 180 – – – 3.65 – – 5 2500 175 – – – 2.99 – – 7 2800 170 – – – 2.81 – – 10 2800 120 – – – 2.58 – – SP 140S-MF1 4 2100 360 – – – – 14.26 – 5 2100 360 – – – – 13.06 – 7 2600 360 – – – – 11.97 – 10 2600 220 – – – – 11.39 – SP 180S-MF1 4 1500 750 – – – – – 45.08 5 1500 750 – – – – – 36.37 7 2300 750 – – – – – 28.57 10 2300 750 – – – – – 24.40 SP 210-MF1 4 1200 1000 – – – – – 75.80 5 1200 1000 – – – – – 63.50 7 1700 1000 – – – – – 52.90 10 1700 1000 – – – – – 47.10 SP 240-MF1 4 1000 1700 – – – – – 5 1000 1700 – – – – – 7 1500 1700 – – – – – 10 1500 1700 – – – – – 1) The limit values in the table apply for S1 continuous duty (ON time > 60% or > 20 min) for a maximum gearbox temperature of +90 °C (194 °F). 1FK7 Synchronous Motors Configuration Manual (PFK7), 10/2005 Edition, 6SN1197-0AD06-0BP1 5-39
Page 1:
��
Page 4 and 5:
Safety information/instructions Thi
Page 6 and 7:
Foreword Target group of the Config
Page 8 and 9:
Foreword Table -3: ESDS information
Page 10 and 11:
Foreword 1FK7 Synchronous Motors vi
Page 12 and 13:
Table of Contents 4.3 Holding brake
Page 14 and 15:
Motor Description Technical data Be
Page 16 and 17:
Motor Description Selection and ord
Page 18 and 19:
Motor Description Selection and ord
Page 20 and 21:
Motor Description Cooling, 1FK7 1.4
Page 22 and 23:
Motor Description Coupling output 1
Page 24 and 25:
Motor Description Armature short-ci
Page 26 and 27:
Motor Description Armature short-ci
Page 28 and 29:
Electrical Connections Rotating the
Page 30 and 31:
Technical Data and Characteristics
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79: Motor Components (Options) Thermal
Page 80 and 81: Motor Components (Options) Encoders
Page 86 and 87: Motor Components (Options) Holding
Page 92 and 93: Gearboxes Selecting/dimensioning ge
Page 94 and 95: Gearboxes Selecting/dimensioning ge
Page 96 and 97: Gearboxes Helical and angled gearbo
Page 126 and 127: Gearbox Planetary gearbox 5.3.2.2 B
Page 130 and 131: Gearbox Planetary gearbox 5.3.2.6 S
Page 132 and 133: Gearbox Planetary gearbox 5.3.3 LP+
Page 134 and 135: Gearbox Planetary gearbox 5.3.3.4 S
Page 136 and 137: Dimension Drawings 1FK7 CT 6.1 1FK7
Page 138 and 139: Dimension Drawings 1FK7 CT Fig. 6-3
Page 144 and 145: Dimension Drawings 1FK7 HD 6.2 1FK7
Page 146 and 147: Dimension Drawings 1FK7 HD Fig. 6-1
Page 148 and 149: Dimension Drawings 1FK7 HD Fig. 6-1
Page 150 and 151: Dimension Drawings 1FK7 motors with
Page 158 and 159: Appendix References Manufacturer/Se
Page 160 and 161: Appendix References /APH7M/ Configu
Page 162 and 163: Index I-2 1FK7 Synchronous Motors C
Page 166: ��
show all

Configuration Manual Synchronous Motors 1FK7 - Siemens ...

Create successful ePaper yourself

Delete template?

Save as template?