Configuration Manual Synchronous Motors 1FK7 - Siemens ...

More documents

Recommendations

Info

Foreword Target group of the Configuration Manual Table -1: Technical Support_normal Technical support Information on the products The Configuration Manual addresses planners and design engineers. It supports you when selecting motors, calculating the drive components, selecting the required accessories as well as when selecting line and motor-side power options. If you have any questions, please contact the following Hotline: Tel.: +49 (0) 180 5050–222 Fax: +49 (0) 180 5050–223 Internet: http://www.siemens.com/automation/support-request Please send any questions about the documentation (e.g. suggestions for improvement, corrections) to the following fax number or email address: Fax: +49 (0) 9131 98–63315 Fax form: Refer to the correction sheet at the end of the document E-mail: motioncontrol.docu@siemens.com Up-to-date information about our products can be found on the Internet at the following address: http://www.siemens.com/motioncontrol 1FK7 Synchronous Motors iv Configuration Manual (PFK7), 10/2005 Edition, 6SN1197-0AD06-0BP1
Table -2: Danger and warning information Danger and warning information Foreword Danger Start-up/commissioning is absolutely prohibited until it has been completely ensured that the machine, in which the components described here are to be installed, is in full compliance with the specifications of Directive 98/37/EC. Only appropriately qualified personnel may commission SIMODRIVE and SIMOVERT MASTERDRIVES drive units and the motors. This personnel must carefully observe the technical customer documentation associated with this product and be knowledgeable about and carefully observe the danger and warning information. Operational electrical equipment and motors have parts and components which are at hazardous voltage levels. When the machine or system is operated, hazardous axis movements can occur. All of the work carried-out on the electrical machine or system must be carried-out with it in a no-voltage condition. SIMODRIVE and SIMOVERT MASTERDRIVES drive units have been designed to be connected to line supplies grounded through a low-ohmic connection (TN line supplies). For additional information please refer to the appropriate documentation for the drive converter systems. Warning The successful and safe operation of this equipment and motors is dependent on professional transport, storage, installation and mounting as well as careful operator control, service and maintenance. For special versions of the drive units and motors, information and data in the catalogs and quotations additionally apply. In addition to the danger and warning information/instructions in the technical customer documentation supplied, the applicable domestic, local and plant-specific regulations and requirements must be carefully taken into account. Caution The motors can have surface temperatures of over +100 °C. This is the reason that temperature-sensitive components, e.g. cables or electronic components may neither be in contact nor be attached to the motor. When connecting-up cables, please observe that they – are not damaged – are not subject to tensile stress – cannot be touched by rotating components. 1FK7 Synchronous Motors Configuration Manual (PFK7), 10/2005 Edition, 6SN1197-0AD06-0BP1 v
Page 1: ��
Page 4 and 5: Safety information/instructions Thi
Page 8 and 9: Foreword Table -3: ESDS information
Page 10 and 11: Foreword 1FK7 Synchronous Motors vi
Page 12 and 13: Table of Contents 4.3 Holding brake
Page 14 and 15: Motor Description Technical data Be
Page 16 and 17: Motor Description Selection and ord
Page 18 and 19: Motor Description Selection and ord
Page 20 and 21: Motor Description Cooling, 1FK7 1.4
Page 22 and 23: Motor Description Coupling output 1
Page 24 and 25: Motor Description Armature short-ci
Page 26 and 27: Motor Description Armature short-ci
Page 28 and 29: Electrical Connections Rotating the
Page 30 and 31: Technical Data and Characteristics
Page 56 and 57:
Technical Data and Characteristics
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Motor Components (Options) Thermal
Page 80 and 81:
Motor Components (Options) Encoders
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Motor Components (Options) Holding
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Gearboxes Selecting/dimensioning ge
Page 94 and 95:
Gearboxes Selecting/dimensioning ge
Page 96 and 97:
Gearboxes Helical and angled gearbo
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Gearbox Planetary gearbox 5.3.2.2 B
Page 128 and 129:
Gearbox Planetary gearbox 5.3.2.4 S
Page 130 and 131:
Page 132 and 133:
Gearbox Planetary gearbox 5.3.3 LP+
Page 134 and 135:
Page 136 and 137:
Dimension Drawings 1FK7 CT 6.1 1FK7
Page 138 and 139:
Dimension Drawings 1FK7 CT Fig. 6-3
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Dimension Drawings 1FK7 HD 6.2 1FK7
Page 146 and 147:
Dimension Drawings 1FK7 HD Fig. 6-1
Page 148 and 149:
Dimension Drawings 1FK7 HD Fig. 6-1
Page 150 and 151:
Dimension Drawings 1FK7 motors with
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Appendix References Manufacturer/Se
Page 160 and 161:
Appendix References /APH7M/ Configu
Page 162 and 163:
Index I-2 1FK7 Synchronous Motors C
Page 166:
��
show all

Configuration Manual Synchronous Motors 1FK7 - Siemens ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?