Configuration Manual Synchronous Motors 1FK7 - Siemens ...

More documents

Recommendations

Info

Foreword Table -3: ESDS information and instructions Caution Motors should be connected-up according to the circuit diagram provided. They must not be connected directly to the three-phase supply because this will damage them. SIMODRIVE and SIMOVERT MASTERDRIVES drive units with AC motors are subject, as part of the type test, to a voltage test corresponding to EN 50178. According to EN 60204-1, Section 19.4, while electrical equipment of industrial machines are being subject to a voltage test, all of the SIMODRIVE and SIMOVERT MASTERDRIVES drive unit connections must be disconnected/withdrawn in order to avoid damaging the SIMODRIVE and SIMOVERT MASTERDRIVES drive units. Note SIMODRIVE and SIMOVERT MASTERDRIVES drive units with motors fulfill, when operational and in dry equipment rooms, the Low-Voltage Directive 73/23/EEC. SIMODRIVE and SIMOVERT MASTERDRIVES drive units with motors fulfill, in the configurations specified in the associated EC Declaration of Conformity, EMC Directive 89/336/EEC. 1FK7 Synchronous Motors vi Configuration Manual (PFK7), 10/2005 Edition, 6SN1197-0AD06-0BP1
ESDS instructions Standards, regulations The appropriate standards, regulations are directly assigned to the functional requirements. Foreword Caution An electrostatic-sensitive device (ESDS) is an individual component, integrated circuit, or module that can be damaged by electrostatic fields or discharges. ESDS regulations for handling boards and equipment: When handling components, make sure that personnel, workplaces, and packaging are well earthed. Personnel in ESD zones with conductive floors may only touch electronic components if they are – grounded through an ESDS bracelet and – wearing ESDS shoes or ESDS shoe grounding strips. Electronic boards should only be touched if absolutely necessary. Electronic boards must not come into contact with plastics or items of clothing containing synthetic fibers. Electronic boards may only be placed on conductive surfaces (table with ESDS surface, conductive ESDS foam rubber, ESDS packing bag, ESDS transport containers). Electronic boards may not be brought close to data terminals, monitors or television sets. (minimum clearance >10 cm). Measurements may only be carried-out on electronic boards and modules if – the measuring instrument is grounded (e.g. via a protective conductor) or – before making measurements with a potential-free measuring device, the measuring head is briefly discharged (e.g. by touching an unpainted blank piece of metal on the control cabinet). 1FK7 Synchronous Motors Configuration Manual (PFK7), 10/2005 Edition, 6SN1197-0AD06-0BP1 vii
Page 1: ��
Page 4 and 5: Safety information/instructions Thi
Page 6 and 7: Foreword Target group of the Config
Page 10 and 11: Foreword 1FK7 Synchronous Motors vi
Page 12 and 13: Table of Contents 4.3 Holding brake
Page 14 and 15: Motor Description Technical data Be
Page 16 and 17: Motor Description Selection and ord
Page 18 and 19: Motor Description Selection and ord
Page 20 and 21: Motor Description Cooling, 1FK7 1.4
Page 22 and 23: Motor Description Coupling output 1
Page 24 and 25: Motor Description Armature short-ci
Page 26 and 27: Motor Description Armature short-ci
Page 28 and 29: Electrical Connections Rotating the
Page 30 and 31: Technical Data and Characteristics
Page 58 and 59:
Technical Data and Characteristics
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Motor Components (Options) Thermal
Page 80 and 81:
Motor Components (Options) Encoders
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Motor Components (Options) Holding
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Gearboxes Selecting/dimensioning ge
Page 94 and 95:
Gearboxes Selecting/dimensioning ge
Page 96 and 97:
Gearboxes Helical and angled gearbo
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Gearbox Planetary gearbox 5.3.2.2 B
Page 128 and 129:
Gearbox Planetary gearbox 5.3.2.4 S
Page 130 and 131:
Page 132 and 133:
Gearbox Planetary gearbox 5.3.3 LP+
Page 134 and 135:
Page 136 and 137:
Dimension Drawings 1FK7 CT 6.1 1FK7
Page 138 and 139:
Dimension Drawings 1FK7 CT Fig. 6-3
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Dimension Drawings 1FK7 HD 6.2 1FK7
Page 146 and 147:
Dimension Drawings 1FK7 HD Fig. 6-1
Page 148 and 149:
Dimension Drawings 1FK7 HD Fig. 6-1
Page 150 and 151:
Dimension Drawings 1FK7 motors with
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Appendix References Manufacturer/Se
Page 160 and 161:
Appendix References /APH7M/ Configu
Page 162 and 163:
Index I-2 1FK7 Synchronous Motors C
Page 166:
��
show all

Configuration Manual Synchronous Motors 1FK7 - Siemens ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?