the Toshiba LCD REGZA 32HL66 - Volume Mart

Recommendations

Info

Selecting the menu language You can choose from three different languages (English, French and Spanish) for the menus and messages. To select the menu language: 1 Press Y and open the Preferences menu. 2 Highlight Menu Language and press c. 3 Press B or b to select your preferred menu language and press T. 4 Press O to close the Preferences menu. 16 Preferences Favorite Channels Closed Caption Mode Off Closed Caption Advanced Input Labeling Menu Language English Channel Browser Setup Navigate ENTER Select CH RTN Back EXIT Exit Chapter 4: Setting up your TV English Français Español Configuring the input source for the ANT terminal To configure the ANT input source: 1 Press Y and open the Setup menu. 2 Highlight Installation and press T. Setup Installation Sleep Timer PC Settings PC Audio HDMI Audio Power-On Mode No Auto Power-Saving Navigate ENTER Select CH RTN Back EXIT Exit 3 (A new set of Installation menu icons appears, as shown below.) Open the Terrestrial menu, highlight Input Configuration, and press T. Terrestrial Input Configuration Channel Program Channel Add/Delete Signal Meter Navigate ENTER Select CH RTN Back EXIT Exit 4 Press C or c to select the input source (Cable or Antenna) for the ANT input on the TV. Input Configuration Antenna 1 In Cable Cancel Done 5 To save your new settings, highlight Done and press T. To revert to your original settings, highlight Cancel and press T.
Programming channels into the TV’s channel memory When you press < or , on the remote control or TV control panel, your TV will stop only on the channels you programmed into the TV’s channel memory. Follow the steps below to program channels into the TV’s channel memory. Programming channels automatically Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are programmed automatically, you can manually add or erase individual channels in the channel memory. Note: You must configure the antenna input source before programming channels (- page 16). If the Antenna input signal type is set to Cable, the automatic channel programming process erases channels that were previously programmed into the TV’s channel memory. If the Antenna input signal type is set to Antenna, the automatic channel programming process adds newly found channels to the existing set of programmed channels (and does NOT erase channels that were previously programmed into the TV’s memory.) To remove an Antenna source channel from the memory, you must manually delete it. To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control. Programming channels when the antenna input is configured for Cable will take substantially longer than when the antenna input is configured for Antenna. This is normal; however, once channel programming is finished, you should not have to repeat the programming process again unless your Cable TV service lineup changes significantly. To program channels automatically: 1 Make sure you have configured the antenna input source (- page 16). 2 Press Y and open the Setup menu. Chapter 4: Setting up your TV 3 Highlight Installation and press T. Setup Installation Sleep Timer PC Settings PC Audio HDMI Audio Power-On Mode No Auto Power-Saving Navigate ENTER Select CH RTN Back EXIT Exit 4 (A new set of Installation menu icons appears, as shown below.) Open the Terrestrial menu, highlight Channel Program, and press T. Terrestrial Input Configuration Channel Program Channel Add/Delete Signal Meter Navigate ENTER Select CH RTN Back EXIT Exit 5 Highlight ANT 1 and then press T to start automatic channel programming. ANT 1 Antenna Scanning channels, please wait ... 52% Abort The TV will automatically cycle through all the antenna channels, and store all active channels in the channel memory. While the TV is cycling through the channels, the message “Scanning channels, please wait” appears (as shown above). 6 To cancel channel programming, either press O or highlight Abort in the on-screen display and press T. When channel programming is finished, press < or , to view the programmed channels. Manually adding and deleting channels in the channel memory After automatically programming channels into the channel memory, you can manually add or delete individual channels. To add or delete channels in the channel memory: 1 Press Y and open the Setup menu. 2 Highlight Installation and press T. (continued) 17
Page 1 and 2: Integrated High Definition LCD Tele
Page 3 and 4: Contents FCC Declaration of Conform
Page 5 and 6: Chapter 1: Introduction TV front an
Page 7 and 8: Preparing the remote control for us
Page 9 and 10: Using the remote control to operate
Page 11 and 12: Programming the remote control to o
Page 13 and 14: Curtis Mathes 001, 005, 009, 012, 0
Page 15: Setup/Installation menu layout Chap
Page 19 and 20: To clear the Favorite Channel lists
Page 21 and 22: Selecting the Power-On Mode You can
Page 23 and 24: Input labeling example: The screen
Page 25 and 26: Using the Home feature When you pre
Page 27 and 28: TheaterWide 3 picture size (for let
Page 29 and 30: Adjusting the picture Selecting the
Page 31 and 32: Digital closed captions You can use
Page 33 and 34: Using the StableSound ® feature Th
Page 35 and 36: Blocking TV programs and movies by
Page 37 and 38: Using the input lock feature You ca
Page 39 and 40: Setting the sleep timer You can set
Page 41 and 42: Chapter 6: Using the TV’s advance
Page 43 and 44: Using the advanced audio settings f
Page 45 and 46: Sound problems Check the antenna/ca
Page 47 and 48: Specifications Note: This model com
Page 49 and 50: Limited Canada Warranty for LCD Tel
Page 51 and 52: Index A Antenna input configuration

the Toshiba LCD REGZA 32HL66 - Volume Mart

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?