the Toshiba LCD REGZA 32HL66 - Volume Mart
the Toshiba LCD REGZA 32HL66 - Volume Mart
the Toshiba LCD REGZA 32HL66 - Volume Mart
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Programming channels into <strong>the</strong><br />
TV’s channel memory<br />
When you press < or , on <strong>the</strong> remote control or TV control<br />
panel, your TV will stop only on <strong>the</strong> channels you programmed<br />
into <strong>the</strong> TV’s channel memory.<br />
Follow <strong>the</strong> steps below to program channels into <strong>the</strong> TV’s<br />
channel memory.<br />
Programming channels automatically<br />
Your TV can automatically detect all active channels in your<br />
area and store <strong>the</strong>m in its memory. After <strong>the</strong> channels are<br />
programmed automatically, you can manually add or erase<br />
individual channels in <strong>the</strong> channel memory.<br />
Note:<br />
You must configure <strong>the</strong> antenna input source before<br />
programming channels (- page 16).<br />
If <strong>the</strong> Antenna input signal type is set to Cable, <strong>the</strong> automatic<br />
channel programming process erases channels that were<br />
previously programmed into <strong>the</strong> TV’s channel memory.<br />
If <strong>the</strong> Antenna input signal type is set to Antenna, <strong>the</strong><br />
automatic channel programming process adds newly found<br />
channels to <strong>the</strong> existing set of programmed channels (and<br />
does NOT erase channels that were previously<br />
programmed into <strong>the</strong> TV’s memory.) To remove an Antenna<br />
source channel from <strong>the</strong> memory, you must manually<br />
delete it.<br />
To tune <strong>the</strong> TV to a channel not programmed in <strong>the</strong> channel<br />
memory, you must use <strong>the</strong> Channel Number buttons on <strong>the</strong><br />
remote control.<br />
Programming channels when <strong>the</strong> antenna input is<br />
configured for Cable will take substantially longer than when<br />
<strong>the</strong> antenna input is configured for Antenna. This is normal;<br />
however, once channel programming is finished, you should<br />
not have to repeat <strong>the</strong> programming process again unless<br />
your Cable TV service lineup changes significantly.<br />
To program channels automatically:<br />
1 Make sure you have configured <strong>the</strong> antenna input source<br />
(- page 16).<br />
2 Press Y and open <strong>the</strong> Setup menu.<br />
Chapter 4: Setting up your TV<br />
3 Highlight Installation and press T.<br />
Setup<br />
Installation<br />
Sleep Timer<br />
PC Settings<br />
PC Audio<br />
HDMI Audio<br />
Power-On Mode<br />
No<br />
Auto<br />
Power-Saving<br />
Navigate ENTER Select CH RTN Back EXIT Exit<br />
4 (A new set of Installation menu icons appears, as shown<br />
below.) Open <strong>the</strong> Terrestrial menu, highlight Channel<br />
Program, and press T.<br />
Terrestrial<br />
Input Configuration<br />
Channel Program<br />
Channel Add/Delete<br />
Signal Meter<br />
Navigate ENTER Select CH RTN Back EXIT Exit<br />
5 Highlight ANT 1 and <strong>the</strong>n press T to start automatic<br />
channel programming.<br />
ANT 1 Antenna<br />
Scanning channels, please wait ...<br />
52%<br />
Abort<br />
The TV will automatically cycle through all <strong>the</strong> antenna<br />
channels, and store all active channels in <strong>the</strong> channel<br />
memory. While <strong>the</strong> TV is cycling through <strong>the</strong> channels,<br />
<strong>the</strong> message “Scanning channels, please wait” appears (as<br />
shown above).<br />
6 To cancel channel programming, ei<strong>the</strong>r press O or<br />
highlight Abort in <strong>the</strong> on-screen display and press T.<br />
When channel programming is finished, press < or , to<br />
view <strong>the</strong> programmed channels.<br />
Manually adding and deleting channels<br />
in <strong>the</strong> channel memory<br />
After automatically programming channels into <strong>the</strong> channel<br />
memory, you can manually add or delete individual channels.<br />
To add or delete channels in <strong>the</strong> channel memory:<br />
1 Press Y and open <strong>the</strong> Setup menu.<br />
2 Highlight Installation and press T.<br />
(continued)<br />
17