6-Channel 10-Model Memory Full Range DSM2™ 2.4GHz Radio ...

More documents

Recommendations

Info

REvOlUTION MIXING (ONly USED wITh NON-hEADING hOlD GyROS) The Revolution Mixing Function mixes tail rotor input with the Throttle/Collective function to counteract torque from the main rotor blades. When set up correctly, the helicopter should climb and descend without a tendency to yaw in either direction. Because torque reaction varies with different power settings, it is necessary to vary the tail rotor pitch at the same time. The DX6i offers two (2) separate revolution mixing programs with independent up and down mixing for each—one for flight mode position 0, and the other for Stunt mode. The U, or Up, mixing adjusts the tail rotor compensation for the mid to high throttle/stick setting, and the D, or Down, mixing adjusts the tail rotor compensation for the mid to low throttle/stick setting. SETTING UP REvOlUTION MIXING First, adjust the helicopter so that it will hover in a neutral position with the tail rotor trim at center. Next, establish the helicopter into a stable hover; then steadily increase the throttle to initiate a stable climb. The body of the helicopter will move in the opposite direction to the main rotor rotation. Increase the U, or Up, setting until the helicopter will climb with no tendency to turn or rotate. At a safe altitude, close the throttle and the helicopter will descend with the body turning in the same direction as the main rotor. Increase the D, or Down, mix until the helicopter descends with no tendency to turn or rotate. When attempting this procedure, throttle stick movements should be slow, and the initial acceleration and deceleration swings should be overlooked. TO ACCESS REvOlUTION MIXING With the transmitter already powered on and the main screen displayed, press and release the ROLLER to enter the ADJUST LIST. Reduce photo to 13.5% ADJUST LIST MODEL SELECT Rotate the ROLLER to the right until REVO MIX is highlighted on screen. Reduce photo to 13.5% ADJUST LIST MIX 2 REVO MIX SETUP LIST Press the roller to access the Revolution Mixing function. 130 SPEKTRUM DX6i • RADIO PROGRAMMING GUIDE Main Main 12
SPEKTRUM DX6i • RADIO PROGRAMMING GUIDE Reduce photo to 13.5% REVO MIX NORM+ STUNT UP 0% UP 0% DN 0% DN 0% Rotate the roller to highlight the desired value that you wish to adjust. Press the roller to access the selected value. Rotate the roller to select adjust the selected value. List After the desired value is programmed press the roller to deselect the value. TO RETURN TO ThE MAIN SCREEN Press and hold the roller for more than 3 seconds then release the roller and the system will return to the main screen. TO RETURN TO ThE ADjUST lIST SCREEN Rotate the roller to highlight LIST then press the roller. SETUP lIST The SETUP list contains the programming functions that are normally only used during the initial setup of the model (i.e. model type, servo reverse, model name). TO RETURN TO ThE MAIN SCREEN Press and hold the roller for more than 3 seconds then release the roller and the system will return to the main screen. TO RETURN TO ThE ADjUST lIST SCREEN Rotate the roller to highlight LIST then press the roller. 131
Page 1 and 2:
Leaders in Spread Spectrum Technolo
Page 3 and 4:
Aircraft Programming Guide ........
Page 5 and 6:
General Information ...............
Page 7 and 8:
DSM2 DUAlINK TEChNOlOGy Your DX6i t
Page 9 and 10:
USING ThIS MANUAl For your convenie
Page 11 and 12:
ChARGING bATTERIES Several versions
Page 13 and 14:
CONTROl STICK lENGTh ADjUSTMENT The
Page 15 and 16:
RECEIvER INSTAllATION Install the m
Page 17 and 18:
hOw TO RANGE TEST ThE DX6I Before e
Page 19 and 20:
3. Establish the desired fail-safe
Page 21 and 22:
RECEIvER POwER SySTEM REqUIREMENTS
Page 23 and 24:
4. Q: Sometimes my receiver loses i
Page 25 and 26:
SERvO REvERSING TO ACCESS SERvO REv
Page 27 and 28:
TRAvEl ADjUST TO ACCESS TRAvEl ADjU
Page 29 and 30:
AIRCRAfT PROGRAMMING GUIDE CONTROl
Page 31 and 32:
SETUP lIST The SETUP list contains
Page 33 and 34:
MODEl TyPE fUNCTION The DX6i featur
Page 35 and 36:
MODEl NAME The Model Name function
Page 37 and 38:
MONITOR The servo monitor screen se
Page 39 and 40:
REvERSE The Reverse Switch function
Page 41 and 42:
ThROTTlE CUT The DX6i offers a Thro
Page 43 and 44:
wING TAIl MIX The DX6i offers three
Page 45 and 46:
DUAl AIlERON wING TyPE SERvO CONNEC
Page 47 and 48:
Rotate the roller to highlight IHN
Page 49 and 50:
SPEKTRUM DX6i • RADIO PROGRAMMING
Page 51 and 52:
RANGE ChECKING A MODEl Rotate the r
Page 53 and 54:
CONTRAST The contrast function allo
Page 55 and 56:
COPy/RESET The COPY function allows
Page 57 and 58:
SETUP lIST SCREEN Rotate the roller
Page 59 and 60:
TO ACCESS ThE ADjUST lIST With the
Page 61 and 62:
Press the roller to access the Mode
Page 63 and 64:
Rotate the ROLLER to the right unti
Page 65 and 66:
Press the roller to access the TRAV
Page 67 and 68:
Press the roller to access the SUB
Page 69 and 70:
Rotate the roller to highlight FLAP
Page 71 and 72:
Press the roller to access the MIX
Page 73 and 74:
SwITCh fUNCTIONS The Mixes can be t
Page 75 and 76:
DIffERENTIAl Note: Only available w
Page 77 and 78:
hElICOPTER PROGRAMMING GUIDE TRANSM
Page 79 and 80: SETUP lIST The SETUP list contains
Page 81 and 82: MODEl TyPE fUNCTION The DX6i featur
Page 83 and 84: MODEl NAME The Model Name function
Page 85 and 86: MONITOR The servo monitor screen se
Page 87 and 88: REvERSE The Reverse Switch function
Page 89 and 90: SwASh TyPE The DX6i offers 2 swashp
Page 91 and 92: ThROTTlE CUT The DX6i offers a Thro
Page 93 and 94: D/R COMbI SwITCh ASSIGNMENT The Dua
Page 95 and 96: TIMER The DX6i features an on scree
Page 97 and 98: RANGE ChECK RANGE CHECK: When activ
Page 99 and 100: POwER SETTING The power setting scr
Page 101 and 102: CONTRAST: Allows the adjustment of
Page 103 and 104: COPy/RESET SCREEN TO ACCESS ThE COP
Page 105 and 106: ADjUST lIST The adjust list contain
Page 107 and 108: MODEl SElECT The DX6i features a me
Page 109 and 110: DUAl RATE AND EXPONENTIAl The Dual
Page 111 and 112: TRAvEl ADjUST The Travel Adjust fun
Page 113 and 114: SUb-TRIM The Sub-Trim function allo
Page 115 and 116: GyRO The gyro function offers two s
Page 117 and 118: SwITCh lOCATION GyRO, f.MODE OR INh
Page 119 and 120: Press the roller to access the Thro
Page 121 and 122: PITCh CURvE Adjustment of the pitch
Page 123 and 124: SwAShPlATE MIXING The Swashplate Mi
Page 125 and 126: PROGRAMMAblE MIXING 1 AND 2 The DX6
Page 127 and 128: Press the roller to deselect the ma
Page 129: TRIM INClUDE fUNCTION Both mixes of
Page 133 and 134: General Notes Radio controlled mode
Page 135 and 136: Daily Flight Checks 1. Check the ba
Page 137 and 138: wARRANTy INSPECTION AND REPAIRS To
Page 139 and 140: PROGRAMMING NOTES: SPEKTRUM DX6i
show all

6-Channel 10-Model Memory Full Range DSM2™ 2.4GHz Radio ...

Create successful ePaper yourself

Delete template?

Save as template?