6-Channel 10-Model Memory Full Range DSM2™ 2.4GHz Radio ...

More documents

Recommendations

Info

PROGRAMMAblE MIXING 1 AND 2 The DX6i offers two programmable mixes that allow stick or switch inputs to control the output of two or more servos. This function allows mixing any one channel to any other channel, or the ability to mix a channel to itself. The mix can remain ON at all times, or it can be switched OFF in flight, using a number of different switches. Mix values are adjustable from -125% to +125%. Each channel is identified by a four-character name (i.e., Aileron - AILE, Elevator - ELEV, etc.). The channel appearing first is the master channel. The second channel is the slave channel. For example, AILE - RUDD would indicate aileron-to-rudder mixing. Each time the aileron stick is moved, the aileron will deflect, and the rudder will automatically move in the direction and to the position based on the value input in the programmable mix screen. Mixing is proportional, so small inputs of the master channel will produce small outputs of the slave channel. Both mixes offer a trim feature, that when activated, the master channel’s trim also affects the slave channel. ACCESSING PROGRAMMAblE MIX 1 OR MIX 2 With the transmitter already powered on and the main screen displayed, press and release the ROLLER to enter the ADJUST LIST. Reduce photo to 13.5% ADJUST LIST MODEL SELECT Rotate the ROLLER to the right until MIX 1 is highlighted on screen. Reduce photo to 13.5% ADJUST LIST FLAPS MIX 1 MIX 2 70 SPEKTRUM DX6i • RADIO PROGRAMMING GUIDE Main Main 6
Press the roller to access the MIX 1 function. SElECTING MASTER AND SlAvE ChANNElS SPEKTRUM DX6i • RADIO PROGRAMMING GUIDE Reduce photo to 13.5% MIX 1 List THRO≥ THRO ACT RATE D 0% U 0% SW ON TRIM INH Rotate the roller to highlight the master (left) channel in the screen. Reduce photo to 13.5% MIX 1 Press the roller to access the master channel selection. List THRO≥ THRO ACT RATE D 0% U 0% SW AIL D/R TRIM INH 71
Page 1 and 2:
Leaders in Spread Spectrum Technolo
Page 3 and 4:
Aircraft Programming Guide ........
Page 5 and 6:
General Information ...............
Page 7 and 8:
DSM2 DUAlINK TEChNOlOGy Your DX6i t
Page 9 and 10:
USING ThIS MANUAl For your convenie
Page 11 and 12:
ChARGING bATTERIES Several versions
Page 13 and 14:
CONTROl STICK lENGTh ADjUSTMENT The
Page 15 and 16:
RECEIvER INSTAllATION Install the m
Page 17 and 18:
hOw TO RANGE TEST ThE DX6I Before e
Page 19 and 20: 3. Establish the desired fail-safe
Page 21 and 22: RECEIvER POwER SySTEM REqUIREMENTS
Page 23 and 24: 4. Q: Sometimes my receiver loses i
Page 25 and 26: SERvO REvERSING TO ACCESS SERvO REv
Page 27 and 28: TRAvEl ADjUST TO ACCESS TRAvEl ADjU
Page 29 and 30: AIRCRAfT PROGRAMMING GUIDE CONTROl
Page 31 and 32: SETUP lIST The SETUP list contains
Page 33 and 34: MODEl TyPE fUNCTION The DX6i featur
Page 35 and 36: MODEl NAME The Model Name function
Page 37 and 38: MONITOR The servo monitor screen se
Page 39 and 40: REvERSE The Reverse Switch function
Page 41 and 42: ThROTTlE CUT The DX6i offers a Thro
Page 43 and 44: wING TAIl MIX The DX6i offers three
Page 45 and 46: DUAl AIlERON wING TyPE SERvO CONNEC
Page 47 and 48: Rotate the roller to highlight IHN
Page 49 and 50: SPEKTRUM DX6i • RADIO PROGRAMMING
Page 51 and 52: RANGE ChECKING A MODEl Rotate the r
Page 53 and 54: CONTRAST The contrast function allo
Page 55 and 56: COPy/RESET The COPY function allows
Page 57 and 58: SETUP lIST SCREEN Rotate the roller
Page 59 and 60: TO ACCESS ThE ADjUST lIST With the
Page 61 and 62: Press the roller to access the Mode
Page 63 and 64: Rotate the ROLLER to the right unti
Page 65 and 66: Press the roller to access the TRAV
Page 67 and 68: Press the roller to access the SUB
Page 69: Rotate the roller to highlight FLAP
Page 73 and 74: SwITCh fUNCTIONS The Mixes can be t
Page 75 and 76: DIffERENTIAl Note: Only available w
Page 77 and 78: hElICOPTER PROGRAMMING GUIDE TRANSM
Page 79 and 80: SETUP lIST The SETUP list contains
Page 81 and 82: MODEl TyPE fUNCTION The DX6i featur
Page 83 and 84: MODEl NAME The Model Name function
Page 85 and 86: MONITOR The servo monitor screen se
Page 87 and 88: REvERSE The Reverse Switch function
Page 89 and 90: SwASh TyPE The DX6i offers 2 swashp
Page 91 and 92: ThROTTlE CUT The DX6i offers a Thro
Page 93 and 94: D/R COMbI SwITCh ASSIGNMENT The Dua
Page 95 and 96: TIMER The DX6i features an on scree
Page 97 and 98: RANGE ChECK RANGE CHECK: When activ
Page 99 and 100: POwER SETTING The power setting scr
Page 101 and 102: CONTRAST: Allows the adjustment of
Page 103 and 104: COPy/RESET SCREEN TO ACCESS ThE COP
Page 105 and 106: ADjUST lIST The adjust list contain
Page 107 and 108: MODEl SElECT The DX6i features a me
Page 109 and 110: DUAl RATE AND EXPONENTIAl The Dual
Page 111 and 112: TRAvEl ADjUST The Travel Adjust fun
Page 113 and 114: SUb-TRIM The Sub-Trim function allo
Page 115 and 116: GyRO The gyro function offers two s
Page 117 and 118: SwITCh lOCATION GyRO, f.MODE OR INh
Page 119 and 120: Press the roller to access the Thro
Page 121 and 122:
PITCh CURvE Adjustment of the pitch
Page 123 and 124:
SwAShPlATE MIXING The Swashplate Mi
Page 125 and 126:
PROGRAMMAblE MIXING 1 AND 2 The DX6
Page 127 and 128:
Press the roller to deselect the ma
Page 129 and 130:
TRIM INClUDE fUNCTION Both mixes of
Page 131 and 132:
SPEKTRUM DX6i • RADIO PROGRAMMING
Page 133 and 134:
General Notes Radio controlled mode
Page 135 and 136:
Daily Flight Checks 1. Check the ba
Page 137 and 138:
wARRANTy INSPECTION AND REPAIRS To
Page 139 and 140:
PROGRAMMING NOTES: SPEKTRUM DX6i
show all

6-Channel 10-Model Memory Full Range DSM2™ 2.4GHz Radio ...

Create successful ePaper yourself

Delete template?

Save as template?