2510 Quilting with Color - Husqvarna Viking

More documents

Recommendations

Info

2510 Quick Project Sun Catcher with Janie Lantz Creating the embroidery: 1. Open 4D Embroidery Professional System. 2. QuickLink to 4D Design Creator . 3. In the Wizard, select Create Express Embroidery. 4. Click Next. 5. Select View Picture, and browse to C:\ 4D embroidery \ Picture Library \ClipArt \Animals \ANIaqua. Click OK and choose the fi sh in a bubble, GO103625. Click Next. 6. No rotation is needed, so click Next. 7. The fi sh is cropped appropriately, so click Next. 8. Choose Fit Design to Hoop. Change Hoop to My Hoops or Husqvarna Viking Designer SE, and choose the150 x 150 DoAll Quilter’s Hoop. Click OK. 9. Click Next. 10. You don’t need to change in Reduce Colors, so click Next. 11. In Choose Thread Colors, check the Automatically Remove Background Color option. Click Next. 12. In the Fabric Advisor, change to Sheer fabric. This will optimize the design for stitching on sheer fabric, removing underlay and stray stitches. Click Next. 13. Review the design in the Preview. Click Finish. 14. In the edit tab, right click to select different areas Sue Hausmann, M’Liss Rae Hawley and Janie Lantz Sewing Supplies: •Husqvarna Viking Sewing and Embroidry Machine •Two 10” x10” squares Green or blue cotton fabric for the sun catcher frame One 10” x10” square Warm & Natural battingDouble-fold bias tape or bias selffabric for fi nishing. 12” x 12” square fi rmly woven sheer such as: Silk Organza tinted with Tsukineko Inks to the color of water & heat set, Voile (cotton can also be tinted) Or: Sparkle or other organza in a pale green or blue. Note: If the organza or voile is too limp, use spray starch or fabric sizing to crisp it •1/2 Yard of 1/8” wide satin ribbon in coordinating color •Embroidery Design created in 4D Embroidery Design Creator Or choose an openwork design from MyEmbroideries.com. •Robison Anton Rayon Embroidery Threads •Empty bobbins, one for each color embroidery thread •Do-All Quilter’s Hoop #920 115-096 (use Heavy inner hoop) •Hoop Ease for the Do-All Quilter’s Hoop #412 74 95 06 •Cut A Round Tool #140 00 16 45 •Rotary cutter with 25mm (1”) or smaller blade •Clear gridded ruler and rotary cutting mat •Sewing thread to match the frame fabric •Clear 1/4” Piecing Foot #412 92 74 47 •Adjustable Bias Binder Foot #412 98 50 45
of the fi sh, and adjust different areas of fi ll. 15. Save as Suncatcher.can. 16. Select 3D Create Stitches to make an embroidery fi le, and save as Suncatcher.vp3. 17. Select 3D Create Stitches again, and use the Send function to send to your Designer SE, a fl oppy disk or USB stick for the Designer I, or a card reader/writer. Stitching your Sun Catcher: 1. Cut a square of organza about 12” square. If necessary, stiffen slightly with spray starch or sizing. 2. Place the outer Do-All Quilter’s hoop on a fl at surface. Lay the organza over the outer hoop, and then lay Hoop Ease on top. Press the Heavy inner hoop into place and fl ip the Quick- Release lever closed. 3. Wind a matching bobbin for each color and trim carefully between each thread change to make it reversible. Stitch using Robison Anton Rayon threads. Turn off the Automatic Jump Stitch Cut Feature if you have it on your machine. 4. Remove from the embroidery hoop and clip any stray threads. 5. Using the Cut-A-Round tool, cut the embroidery into a 6” circle. 6. Using the Cut-A-Round tool, cut 5” circles in the exact center of each 10” piece of quilting cotton. 7. Quarter and pin-mark the organza circle and one cotton square. 8. Lay the organza embroidery right-side up on a fi rm surface. Lay one fabric frame over it, right side up. Flip the top edge of the frame down toward the center of the organza, so the frame and organza are right-sides together where they will be seamed. Match the quarter marks,
Page 1 and 2: 2510 Quilting with Color with M’L
Page 3: Telling your story through piecing

2510 Quilting with Color - Husqvarna Viking

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?