Carnival Castle

More documents

Recommendations

Info

Step 5 268 H132 H11 H3 302 Main Beam, Facia, and Ladder Assembly *NOTE: Hardware should not be fully tightened at this time. 1. On a flat surface, position Main Beams (266), Angled Facias (302), and previously assembled ladders as shown and attach using 3/8" Hardware (H3) (H11) (H34) (H132). Ladders, Main Beams, and Angled Facias must be positioned as shown. H34 277 H132 H11 266 23 A H3 H34 277 302 H34 266 H3 H3 H11 H132 H11 DETAIL A H132 273 302
Step 6 COUNTER-SUNK HOLES 268 FACES FLUSH 266 277 A DETAIL B 302 Main Beam, Facia, and Ladder Assembly *NOTE: This step requires two or more people to complete. *NOTE: For ease of assembly, have all required parts and hardware in close proximity. *NOTE: Pre-drill holes for all Lag Bolts with the appropriate drill bit. *NOTE: Do not fully tighten hardware at this time. *NOTE: 3/8" Hardware (H28) is shown but will not be installed until Step 8. 1. Pick up on the Step/Rung Ladder assembly so the outside faces of the Ladder Legs (268) (277) are flush with the angled faces of Angled Facias (302) and Main Beams (266) (as shown in DETAIL B). 2. Position Corner Uprights (272) between Main Beams and Angled Facias with counter-sunk holes facing one another, and attach to Facias and Main Beams using 3/8" Hardware (H3) (H11) (H34) (H132) (as shown in DETAIL A). *NOTE: Use a carpenter's square to ensure Corner Uprights (272) are square with Facias and Main Beams. 3. Finish securing the Ladder assembly by attaching Ladder Legs (268) (277) to Facias, Main Beams, and Corner Uprights using 1/4" Hardware (H1), 5/16" Hardware (H108), and 3/8" Hardware (H3) (H117) (as shown in DETAIL A). Gaps between Corner Uprights (272) and Ladders Legs should be minimal. 4. Repeat parts 1 through 3 for the Rock Wall Ladder assembly. 272 B 277 STEP/RUNG LADDER ASSEMBLY 24 CARPENTER'S SQUARE H108 H132 268 H1 H117 302 NO GAPS H11 H3 H3 H1 DETAIL A ROCK WALL LADDER ASSEMBLY 273 302 H108 272 H34 266 H28
Page 1 and 2: Carnival Castle Assembly Instructio
Page 3 and 4: Safety Instructions Rules for Safe
Page 5 and 6: Maximum Fall Height is 8' TABLE 3.1
Page 7 and 8: COMMONLY ASKED QUESTIONS Question:
Page 9 and 10: 276 277 278 279 384 346 283 285 289
Page 11 and 12: 261 262 2 @ 1 x 6 x 26 1/8" NOTCHED
Page 13 and 14: N16 N20 1 @ TIRE (5-40-0047) 1 @ SH
Page 15 and 16: H5 H14 H164 H194 Hardware for Assem
Page 17 and 18: Hardware for Assembly *NOTE: Thread
Page 19 and 20: 382 379 378 PARTS IDENTIFICATION 36
Page 21 and 22: H116 Step 2 H3 H191 303 ENDS FLUSH
Page 23: H117 H3 Step 4 269 286 45" H116 H3
Page 27 and 28: Step 8 H11 H17 H3 H28 302 H55 H4 Fr
Page 29 and 30: Step 10 FRONT FACIA (292) MUST BE L
Page 31 and 32: Step 12 N13 N31 N15 Swing Assembly
Page 33 and 34: Step 14 N10 H11 H17 H28 H56 H4 N29
Page 35 and 36: Step 15 Continued from previous pag
Page 37 and 38: Step 17 Rock and Rope Installation
Page 39 and 40: Step 19 INSET A H194 256 258 INSET
Page 41 and 42: Step 21 H167 H167 N6 N5 H167 18" Sa
Page 43 and 44: Step 23 264 N41 Tarp Installation *
Page 45 and 46: Step 25 280 280 Monkey Bar Assembly
Page 47 and 48: Step 27 1. Install 3/8" Hardware (H
Page 49 and 50: Step 29 1. Position Roof Frame Side
Page 51 and 52: Step 31 Dormer Installation 1. Posi
Page 53 and 54: Step 33 *NOTE: Over-tightening scre
Page 55 and 56: Step 35 298 299 298 298 H154 INSET
Page 57 and 58: Step 37 H93 Stake Installation *NOT
Page 59: Limited Ten-Year, Five-Year, and On

Carnival Castle

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?