Carnival Castle

More documents

Recommendations

Info

Step 16 H14 H14 H24 H196 INSET A N16 Tire Swing Installation 1. Center Tire Swivel (N25) on the middle Deck Boards and mark the location of the mounting holes. The holes should hit towards the middle of the Deck Boards and be approximately 12" - 13" from the front edge of the Deck Boards. Drill through Deck Boards using a 9/16" drill bit. Drill slowly to prevent drilling blowouts. 2. Attach the Tire Swivel (N25) though the Tire Swing Block (290) and the Deck Boards using 1/2" Hardware (H4) (H12) (H18) (H29) (H64) and 3/4" Hardware (H5). 3. Attach Spring Clips (N27) to Tire Chains (N12). Hook Spring Clips (N27) to Tire Swivel (N25). 4. Install 3/8" Hardware (H196) (H14) (H24) in Tire (N16) using pre-drilled holes (as shown in INSET A). Attach Tire (N16) to Tire Chains (N12) using C-Clips (N30). 35 H12 H18 H4 290 N25 H29 H5 H64 N27 N12 N30 H196 N16
Step 17 Rock and Rope Installation 1. Attach Rocks (N22) to Rock Wall Boards (284) (285) using 1/4" Hardware (H7) (H192) and 1/4" T-Nuts (H32) that were installed in Step 3. Use four 1/4" SAE Washers (H7) for each Rock. *WARNING: TO PREVENT THE RISK OF STRANGULATION, THREE KNOTS MUST BE TIED IN ROPE AND ROPE MUST BE SECURE AT BOTH ENDS. ROPE MUST BE TIGHT ENOUGH THAT IT CANNOT BE LOOPED BACK ON ITSELF, AND NO MORE THAN 12" OF ROPE SHOULD BE LEFT AFTER TYING DOUBLE KNOTS AT THE TOP AND BOTTOM OF THE ROPE. 2. Thread 12' Rope (N1) up through the bottom of the Front Beam (271) and tie a double knot. 3. Tie three single knots evenly spaced along the Rope (N1). 4. Thread Rope through Rock Wall Board w/Rope Hole (286) and tie a double knot on the backside. DOUBLE KNOT 271 SINGLE KNOT 286 36 284 285 N1 N22 N22 H32 INSET A DOUBLE KNOT ON BACK H7 H192
Page 1 and 2: Carnival Castle Assembly Instructio
Page 3 and 4: Safety Instructions Rules for Safe
Page 5 and 6: Maximum Fall Height is 8' TABLE 3.1
Page 7 and 8: COMMONLY ASKED QUESTIONS Question:
Page 9 and 10: 276 277 278 279 384 346 283 285 289
Page 11 and 12: 261 262 2 @ 1 x 6 x 26 1/8" NOTCHED
Page 13 and 14: N16 N20 1 @ TIRE (5-40-0047) 1 @ SH
Page 15 and 16: H5 H14 H164 H194 Hardware for Assem
Page 17 and 18: Hardware for Assembly *NOTE: Thread
Page 19 and 20: 382 379 378 PARTS IDENTIFICATION 36
Page 21 and 22: H116 Step 2 H3 H191 303 ENDS FLUSH
Page 23 and 24: H117 H3 Step 4 269 286 45" H116 H3
Page 25 and 26: Step 6 COUNTER-SUNK HOLES 268 FACES
Page 27 and 28: Step 8 H11 H17 H3 H28 302 H55 H4 Fr
Page 29 and 30: Step 10 FRONT FACIA (292) MUST BE L
Page 31 and 32: Step 12 N13 N31 N15 Swing Assembly
Page 33 and 34: Step 14 N10 H11 H17 H28 H56 H4 N29
Page 35: Step 15 Continued from previous pag
Page 39 and 40: Step 19 INSET A H194 256 258 INSET
Page 41 and 42: Step 21 H167 H167 N6 N5 H167 18" Sa
Page 43 and 44: Step 23 264 N41 Tarp Installation *
Page 45 and 46: Step 25 280 280 Monkey Bar Assembly
Page 47 and 48: Step 27 1. Install 3/8" Hardware (H
Page 49 and 50: Step 29 1. Position Roof Frame Side
Page 51 and 52: Step 31 Dormer Installation 1. Posi
Page 53 and 54: Step 33 *NOTE: Over-tightening scre
Page 55 and 56: Step 35 298 299 298 298 H154 INSET
Page 57 and 58: Step 37 H93 Stake Installation *NOT
Page 59: Limited Ten-Year, Five-Year, and On

Carnival Castle

Create successful ePaper yourself

Delete template?

Save as template?