Carnival Castle

More documents

Recommendations

Info

Step 13 N12 N30 N12 12" INSET A N30 4 Chain Tire Swing Assembly 1. Attach Eye Bolts (H196) to Tire (N169) using 3/8" Hardware (H14) (H24) (as shown in Detail A). *NOTE: Make sure Eye Bolts (H196) are orientated as shown using the 12" measurement. 2. Open C-Links (N30). Divide the six Chains (N12) into groups of three Chains. Connect each group of Chains together using C-Links (N30) (as shown in Inset A). 3. Attach Chains (N12) to Eye Bolts (H196) using C-Links (N30) (as shown in Inset A). 4. Securely close all C-Links (N30) by tightening with a crescent wrench. H196 31 H14 H24 N169 DETAIL A H196 H14
Step 14 N10 H11 H17 H28 H56 H4 N29 H139 H3 77 H3 H135 N29 N26 H3 H24 H11 H28 N170 H3 H116 A-Frame Assembly and Swing Hanger Installation *NOTE: It is possible to modify your 3 Position Swing Beam to a 2 Position Swing Beam for use in small yards. See Step 38, page 57 for instructions on how to modify the 3 Position Swing Beam to a 2 Position Swing Beam. Proceed with the following steps after making the modifications. 1. Attach Swing Hangers (N26) to Swing Beam (346) using 3/8" Hardware (H3) (H11) (H24) (H28) (H135) and 3/8" Bolt Cup (N29). *SUGGESTION: Use a box wrench or locking pliers to hold on to Hex Head Bolts (H135). 2. Position Plaque (N83) in the approximate position shown and attach to Swing Beam using Hardware (H158). 3. Attach Swing Beam Plate (N10) to Swing Beam (346) using 3/8" Bolt Cup (N29), 3/8" Hardware (H3) (H11) (H17) (H28) (H56), and 1/2" Hardware (H4). Do not fully tighten hardware at this time. 4. Attach Upper A-Frame Block (81) and Lower A-Frame Block (82) using 3/8" Hardware (H3) (H116). 5. Attach A-Frame Legs (77) to A-Frame Block assembly using 45 Bracket (N170) and 3/8" Hardware (H139) (H3) (H11) (H17). Do not fully tighten hardware at this time. 6. Lay assembly on the ground with A-Frame Legs (77) pointing in opposite directions. N83 H158 81 32 82 H3 H11 346 H17 77
Page 1 and 2: Carnival Castle Assembly Instructio
Page 3 and 4: Safety Instructions Rules for Safe
Page 5 and 6: Maximum Fall Height is 8' TABLE 3.1
Page 7 and 8: COMMONLY ASKED QUESTIONS Question:
Page 9 and 10: 276 277 278 279 384 346 283 285 289
Page 11 and 12: 261 262 2 @ 1 x 6 x 26 1/8" NOTCHED
Page 13 and 14: N16 N20 1 @ TIRE (5-40-0047) 1 @ SH
Page 15 and 16: H5 H14 H164 H194 Hardware for Assem
Page 17 and 18: Hardware for Assembly *NOTE: Thread
Page 19 and 20: 382 379 378 PARTS IDENTIFICATION 36
Page 21 and 22: H116 Step 2 H3 H191 303 ENDS FLUSH
Page 23 and 24: H117 H3 Step 4 269 286 45" H116 H3
Page 25 and 26: Step 6 COUNTER-SUNK HOLES 268 FACES
Page 27 and 28: Step 8 H11 H17 H3 H28 302 H55 H4 Fr
Page 29 and 30: Step 10 FRONT FACIA (292) MUST BE L
Page 31: Step 12 N13 N31 N15 Swing Assembly
Page 35 and 36: Step 15 Continued from previous pag
Page 37 and 38: Step 17 Rock and Rope Installation
Page 39 and 40: Step 19 INSET A H194 256 258 INSET
Page 41 and 42: Step 21 H167 H167 N6 N5 H167 18" Sa
Page 43 and 44: Step 23 264 N41 Tarp Installation *
Page 45 and 46: Step 25 280 280 Monkey Bar Assembly
Page 47 and 48: Step 27 1. Install 3/8" Hardware (H
Page 49 and 50: Step 29 1. Position Roof Frame Side
Page 51 and 52: Step 31 Dormer Installation 1. Posi
Page 53 and 54: Step 33 *NOTE: Over-tightening scre
Page 55 and 56: Step 35 298 299 298 298 H154 INSET
Page 57 and 58: Step 37 H93 Stake Installation *NOT
Page 59: Limited Ten-Year, Five-Year, and On

Carnival Castle

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?