TERMOCAMINO 650 - 800
TERMOCAMINO 650 - 800
TERMOCAMINO 650 - 800
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Termocamino <strong>650</strong> - <strong>800</strong><br />
To perform a correct first lighting of products treated with paints for high temperatures, the following must<br />
be considered:<br />
• The construction materials of the products in question are not homogeneous; in fact there are parts<br />
in cast iron, steel, refractory material, and majolica ceramic.<br />
• The temperature to which the body of the product is subject is not homogeneous: from zone to zone<br />
variable temperatures are recorded between 300°C to 500°C.<br />
• During its lifetime, the product is subject to alternating cycles of lighting and shutdown during the<br />
same day and to cycles of intense usage or absolute rest along with the changing seasons.<br />
• The new appliance, before being able to be defined as seasoned, must undergo various cycles of<br />
start-up to allow all the materials and the paint to complete the various elastic stresses.<br />
• In particular initially, you may notice the emission of the typical odours of metals subjected to high<br />
thermal stress and of still fresh paint. This paint, though it is baked during manufacture at 250°C fo r<br />
a number of hours, must be subject to a temperature of 350°C numerous times and for a certain<br />
duration before it becomes perfectly incorporated with the metallic surfaces.<br />
It is therefore important to follow these simple measures during the lighting phase:<br />
7) Make sure that there is good air exchange in the place where the appliance is installed.<br />
8) During the first lightings, do not excessively load the combustion chamber (about half the quantity<br />
indicated in the instruction manual), and keep the product lit for at least 6-10 hours continuously,<br />
with the registers less open than that indicated in the instruction manual.<br />
9) Repeat this operation for at least 4-5 or more times, depending on your availability.<br />
10) Subsequently, increase the load (in any case following that which is described in the instruction<br />
booklet regarding the maximum load) and if possible keep long periods of lighting, avoiding, at least<br />
in this initial phase, brief cycles of lighting-shutdown.<br />
11) During the first lightings, no object must be set on the appliance and in particular on the<br />
enamelled surfaces. The enamelled surfaces must not be touched during heating.<br />
12) Once the “road test” has been passed, your product can be used like a car engine, avoiding<br />
brusque heating with excessive loads.<br />
ATTENTION: during the first lightings there could be a solid smokes condensation with a small<br />
escape of water from the thermo-fireplace: this event will expire in a very short time but if it<br />
persists it will be necessary to check the chimney draught.<br />
IMPORTANT:<br />
Only after a few days of operation (the time necessary for determining that the appliance is<br />
operating correctly), you can begin to assemble the aesthetic facing.<br />
11. NORMAL OPERATION<br />
After positioning the air register correctly, insert the hourly load of wood (see Chapter 20 – Chapter 21),<br />
avoiding overloads that could cause anomalous stresses or deformation.<br />
Failure to observe this rule will void the warranty.<br />
The heat emission is regulated with the register situated on the front of the appliance, which should be<br />
opened according to your heating needs.<br />
The regulation of the register necessary for obtaining the nominal heat output with depression to the<br />
chimney of 17 - 20 Pa (= 1.7 – 2 mm of column of water) is as follows:<br />
Fuel<br />
Primary air<br />
Flat Wood Open<br />
Prismatic Wood Open<br />
In the event that the water temperature exceeds the tripping temperature of the safety devices,<br />
immediately suspend the feeding of wood, and make sure that the water temperature and the flame<br />
decrease, eliminating the causes of the overheating (if necessary by closing the air register).<br />
If the water system is connected in the thermo-fireplace, the hot water tap can be opened to speed<br />
up the cooling of the appliance.<br />
Instruction Manual – Rev.07 – EN 33