102386 Kurzbedienungsanleitung FOCX32 ... - Elcon Systemtechnik

Weitere Magazine

Empfehlungen

Info

FOCX32 The data signal is bidirectionally transmitted via the cable TV distribution network. The coaxial cabling setup (e.g. in tree or star structure) is uncritical. All ELCONnect coax modems have equal access rights to the medium. The transmission uses a multiplexing procedure, allowing for an automatical data rate adaptation, subject to the connection quality. This both robust and effective transmission method offers a reliable data transfer even under the most difficult circumstances. When several units are used, the data rate is dynamically shared. Device set-up is effected by means of a configuration file, which allows the user to define all the parameters needed for transmission, such as bandwidth allocation to the Clients, Quality- Of-Service parameters, access permissions or transmission levels. If required, certain frequencies can be spared out for transmission – a feature that may be necessary in hotel networks to prevent interference with the transmission of Pay-TV signals. Apart from this, it is also possible to reduce the signal level over an entire frequency range. The optical Master represents the interface between the unidirectional cable TV distribution networks and the bidirectional telecommunications network. For example, the FOCX32 can be linked to a router, thus feeding the data signal at the outlet of the headend or the network node into the coaxial cable network. The signal is then distributed to all TV outlets installed within a radius of max. 750 m (depending on the environment). Through the TV splitter (included in delivery) the signals from the Clients are supplied to the TV socket in the client´s flat. This can be easily done without requiring further costs, since all the needed components are included in delivery. The client is connected with the network interface card of the PC via a patch cable. So he can use the "Internet access" without any further configuration of the personal computers to be linked. The ELCONnect coax modems are responsible for processing and modulation of the data transmitted through the coaxial cable network, as well as for the provision of all interfaces for optical fiber and coaxial link. Thanks to their functionality, the modems, after being connected to a server or router (FOCX32) or, respectively, to the network interface card of the relevant PC or router (Client), are used both as transmitter and receiver of the information to be exchanged. Hereby the EL- CONnect coax system functions as bridge between server or router, on the one side, and the terminal equipment, such as PC or set-top boxes, on the other. IP addresses, for example, are dynamically (DHCP) or statically allocated by the server or router to the linked terminals (PC) the same way as it is normally done within a standard PC network. So the modems are able to provide via the cable television network different services like an Internet access. To ensure the integrity within a complex network, the Clients cannot communicate among themselves, but only with the related optical Master. 28 Version: 2009/01/29
FOCX32 1.4 Structure of the ELCONnect coax FOCX32 The scheme below shows the main components of the ELCONnect coax FOCX32 and their location in the device. As for installation, the test socket (allowing for measurements) and the fuse panel are of relevance. Power pack Bi-directional Single Fiber Transceiver Test point F-socket for DATA signal spectrum ELCONnect coax Master Moduls Outlet TV/DATA Client side (SIGNAL OUT) 1.5 Power supply Input TV Headend side (TV IN) Power inserter Figure 3: Main parts of an ELCONnect coax FOCX32 Fuse panel for remote power supply Fiber Management Cable feedthrough for optical fiber Mains connection Diplexer Moduls By default the ELCONnect coax FOCX32 is delivered with two versions for power supply. The 230 V power pack allows for a stationary operation with local power supply from the 230 V electricity network. The remote power supply module provides the option to have the equipment powered over the coax television cable. Please pay attention to the device version when connecting the equipment to the power supply. You will find relevant hints on the type plate. Note that only the 230 V device version has been equipped with a mains cable with standardized Euro flat-cable plug. Version: 2009/01/29 29
Seite 1 und 2: coax Fiber Optical Coax MDU FOCX32
Seite 3 und 4: FOCX32 • Warnung vor gefährliche
Seite 5 und 6: FOCX32 • Warning of dangerous las
Seite 7 und 8: FOCX32 Contents ENGLISH ...........
Seite 9 und 10: FOCX32 ELCONnect coax Master32 Gate
Seite 11 und 12: FOCX32 1.4 Aufbau ELCONnect coax FO
Seite 13 und 14: FOCX32 Das Gerät darf nicht an bre
Seite 15 und 16: FOCX32 Anschlussadapter Bild 7: Kab
Seite 17 und 18: FOCX32 Aktuelle Spleißgeräte sind
Seite 19 und 20: FOCX32 2.8 Anschließen der Verbind
Seite 21 und 22: FOCX32 Fernspeisenetzteil Fernspeis
Seite 23 und 24: FOCX32 2.11 Anzeigeelemente (LEDs)
Seite 25 und 26: FOCX32 CATV Durchgangsdämpfung typ
Seite 27 und 28: FOCX32 gangstechnologien informiere
Seite 29: FOCX32 ELCONnect coax Master32 Gate
Seite 33 und 34: FOCX32 The device must not be mount
Seite 35 und 36: FOCX32 Adapter connector Figure 7:
Seite 37 und 38: FOCX32 Common splice units can be u
Seite 39 und 40: FOCX32 2.8 Installation of the conn
Seite 41 und 42: FOCX32 60 60 Remote feeding module
Seite 43 und 44: FOCX32 2.11 Display elements (LEDs)
Seite 45 und 46: FOCX32 CATV Transmission loss typic
Seite 47: FOCX32 Note: This documentation may

102386 Kurzbedienungsanleitung FOCX32 ... - Elcon Systemtechnik

Erfolgreiche ePaper selbst erstellen

Template löschen?

Als Template speichern?