Pan/Tilt Head with Multiple Protocol Interface VPT-601 ... - Belcom
Pan/Tilt Head with Multiple Protocol Interface VPT-601 ... - Belcom
Pan/Tilt Head with Multiple Protocol Interface VPT-601 ... - Belcom
Erfolgreiche ePaper selbst erstellen
Machen Sie aus Ihren PDF Publikationen ein blätterbares Flipbook mit unserer einzigartigen Google optimierten e-Paper Software.
ANHANG 1B - Lage der Schalter S1-S4 auf der Steuerplatine (ab Seriennummer 38312)<br />
APPENDIX 1B - Circuit board switch locations (from serial number 38312)<br />
Jumper Functions:<br />
Werkeinstellungen – fett / Default setup – bold<br />
Address selected by S2<br />
Switch No. 1 2 3 4 5 6 7 8 9 10<br />
Address if switch ON 1 2 4 8 16 32 64 128 256 512<br />
Function selected by S3<br />
1 2 3 <strong>Protocol</strong> 4 5 6 7 ** ) 8 9 10<br />
Set RS 120 Ohm Termination<br />
J4 13, 14 close ON<br />
J4 13, 14 open OFF<br />
Videor OFF OFF OFF<br />
AUX-<br />
<strong>Multiple</strong>xer<br />
<strong>Tilt</strong><br />
Reference<br />
Offset<br />
OFF: 0°;<br />
ON: -45°<br />
Pelco D ON OFF OFF<br />
Pelco P OFF ON OFF<br />
ON OFF<br />
OFF: lens >1V,<br />
ON: lens >6V; * )<br />
Philips ON ON OFF<br />
Siemens OFF OFF ON<br />
(siehe<br />
Tabelle 2,<br />
S. 15 / see<br />
table 2,<br />
p. 35)<br />
ON OFF ON<br />
Select RS / TTY<br />
J4 9, 11 close / open<br />
J4 10, 12 close / open<br />
J4 7, 9 open / close<br />
J4 8, 10 open / close<br />
Fastrax<br />
IIE<br />
Select RS-485 / RS-422<br />
J4 5, 6 close / open<br />
J4 3, 4 close / open<br />
J4 1, 2 close / open<br />
* ) OFF: Für Objektivmotoren mit niedriger Anlaufspannung (> 1V) /<br />
For lens motors <strong>with</strong> low starting voltage (>1V)<br />
ON: Für Objektivmotoren mit höherer Anlaufspannung (> 6V) /<br />
For lens motors <strong>with</strong> high starting voltage (>6V)<br />
** ) Ab der Firmware-Version VI200 nur mit erweiterten Preset-Befehlen<br />
konfigurierbar, siehe ANHANG 2<br />
For Firmware VI200 and higher only configurable <strong>with</strong> extended Preset<br />
commands, see APPENDIX 2<br />
Function selected by S4<br />
1 2 3 4 5 6 7 ** ) 8 9 10<br />
<strong>VPT</strong>-<strong>601</strong>/651<br />
OFF<br />
ON: Address 1024<br />
No Function<br />
OFF: Mounting direction normal<br />
ON: Mounting direction upside down<br />
Beschleunigung / Acceleration<br />
ON: 0.4sec.; OFF: 0.2sec.<br />
OFF: Heater off during <strong>Pan</strong>/<strong>Tilt</strong><br />
ON: Heater on during <strong>Pan</strong>/<strong>Tilt</strong><br />
Baud Rate<br />
OFF OFF OFF 300<br />
ON OFF OFF 600<br />
No Function<br />
No Function<br />
OFF ON OFF 1200<br />
ON ON OFF 2400<br />
OFF OFF ON 4800<br />
ON OFF ON 9600<br />
OFF ON ON 19200<br />
ON ON ON –<br />
46