2006 Ford Racing Performance Parts Catalog - Chromwerk

ALUMINUM 302/351 STREET/RACE BLOCKS
302 ALUMINUM
WET OR DRY SUMP BLOCK,
380 CID CAPACITY
M-6010-F302* 8.200" Deck Height
Heavy duty, lightweight alternative
to cast iron.
• 356-T7 aluminum block with 4-bolt,
steel billet main caps
• Iron sleeves, bore range 4.000-4.155"
• Siamese cylinder bores, 5.200" long
• Finished main bearing bore
for 2.248" journal diameter
• Uses common OD cam bearings,
part number M-6261-J351/R351.
See page 68
• Weighs approximately 100 lbs.
• Available from Raceparts Distribution, Inc.
(704) 892-8688
NOTE: Siamese blocks are solid
casting between the cylinder
bores. There are no water
passages between them. This is
done to increase the strength of
the block.
351 ALUMINUM RACE BLOCK
M-6010-C450*
• 4" to 4.125" bore capacity
• Centrifically cast liners
• All aluminum water jacket and oil galley plugs
• 9.2" deck height
• Four bolt main journals one through five
• Dry sump design
• 2.750" main bearing journals
• Enclosed cam tunnel
• Light weight at only
92 lbs.
• 7075 aluminum
main caps
• Recommended for
Dirt late model, Sprint,
410 Sprint
• Use with M-6701-B351
crankshaft seal, M-6269-C450 cam thrust retainer,
M-6268-C450 timing chain and gear set, M-6059-C450
timing cover, and M-6261-C450 cam bearings
302 ALUMINUM
WET OR DRY SUMP BLOCK,
396 CID CAPACITY
M-6010-F87* 8.700" Deck Height
Heavy duty, lightweight alternative
to cast iron.
• 356-T7 aluminum block with 4-bolt,
steel billet main caps
• Iron sleeves, bore range 4.000-4.155"
• Siamese cylinder bores, 5.700" long
• Finished main bearing bore
for 2.248" journal diameter
• Uses common OD cam bearings,
part number M-6261-J351/R351
(special order machining
for roller cam bearings). See page 68
• Weighs approximately 115 lbs.
• Available from Raceparts Distribution, Inc.
(704) 892-8688
351 ALUMINUM
WET OR DRY SUMP BLOCK,
427 CID CAPACITY
M-6010-X352* 9.200" Deck Height
Heavy duty, lightweight alternative
to cast iron.
• 356-T7 aluminum block with 4-bolt,
steel billet main caps
• Iron sleeves, bore range 4.000-4.155"
• Siamese cylinder bores, 5.700" long
• Finished main bearing bore
for 2.248" journal diameter
• Uses common OD cam bearings,
part number M-6261-J351/R351
(special order machining
for roller cam bearings). See page 68
• Weighs approximately 117 lbs.
• Available from Raceparts Distribution, Inc.
(704) 892-8688
*Not legal for sale or use on pollution-controlled motor vehicles. **Direct replacement part.
351 ALUMINUM
WET OR DRY SUMP BLOCK,
427 CID CAPACITY
M-6010-X351* 9.200" Deck Height
Heavy duty, light weight alternative
to cast iron.
• 356-T7 aluminum block with 4-bolt,
steel billet main caps
• Iron sleeves, bore range 4.000-4.155"
• Siamese cylinder bores, 5.700" long
• Finished main bearing bore
for 2.749" journal diameter
• Uses common OD cam bearings,
part number M-6261-J351/R351
(special order machining
for roller cam bearings). See page 68
• Weighs approximately 117 lbs.
• Available from Raceparts Distribution, Inc.
(704) 892-8688
351 ALUMINUM
WET OR DRY SUMP BLOCK,
454 CID CAPACITY
M-6010-Z351* 9.500" Deck Height
Heavy duty, lightweight alternative
to cast iron.
• 356-T7 aluminum block with 4-bolt,
steel billet main caps
• Iron sleeves, bore range 4.000-4.155"
• Siamese cylinder bores, 6.000" long
• Finished main bearing bore
for 2.749" journal diameter
• Uses common OD cam bearings,
part number M-6261-J351/R351
(special order machining
for roller cam bearings). See page 68
• Weighs approximately 124 lbs.
• Available from Raceparts Distribution, Inc.
(704) 892-8688
CAM THRUST PLATE FOR C450 BLOCK
M-6269-C450
• Thrust plate fits only
M-6010-C450
block
• Low friction
needle bearing
thrust plate
TIMING CHAIN COVER FOR C450 BLOCK
M-6059-C450*
• Fits 9.200" deck aluminum height
“superblock” M-6010-C450
• Kit contains timing cover,
crank seal and gasket
www.fordracingparts.com 65
ENGINE
COMPONENTS