OmniLink II Press Automation Control Automatic ... - LINK Systems

More documents

Recommendations

Info

Figure 3-9 Auto-Counterbalance with Type “A” Integrated Valve Figure 3-10 Auto-Counterbalance with Type "C" Integrated Valve October 16, 2008 Manual Version 1.1 3-8
Section 3.3.1 Counterbalance Pressure Transducer Mounting The system uses an automatic method of control in which the fill valve or dump valve is energized to raise or lower the pressure of the system and a pressure transducer is used to “tell” the Automatic Setup board the system pressure. The pressure transducer is constantly monitored to verify that the system is at the proper pressure. When filling or dumping air into or out of the counterbalance, the transducer tells the system when to stop. Because air pressure drops occur across air lines when filling or dumping, proper placement of the pressure transducer is very important for correct operation of the system. Possible pressure transducer mounting locations from best to worst are (refer to Figure 3.11): a) A spare port on the counterbalance surge tank. b) The same port that the safety pop-off valve is mounted on if it has its own port on the surge tank. c) Right at the outlet on the surge tank that goes to the counterbalance cylinder. d) Right at the inlet on the surge tank from the Fill/Dump valves. e) If there is no surge tank the pressure transducer should be mounted right at the inlet on the counterbalance cylinder. Figure 3-11 Acceptable Locations for Mounting counterbalance Pressure Transducer October 16, 2008 Manual Version 1.1 3-9
Page 1: OmniLink II Press Automation Contro
Page 4 and 5: Section 4.2.2.2 Calibrating a Rotar
Page 6 and 7: Section 1.2 Cushion Control Quick d
Page 8 and 9: say “CHANGE TEXT” or “CHANGE
Page 10 and 11: the password the operator can reset
Page 12 and 13: Setpoint: Actual Shutheight Fault:
Page 15 and 16: Section 3 Installation Section 3.1
Page 17 and 18: After installing the plug-on boards
Page 19 and 20: The 4 pin plug supplied for connect
Page 21: October 16, 2008 Manual Version 1.1
Page 25 and 26: Figure 3-13 Cushion System with Typ
Page 27 and 28: slide adjust. Slide adjust motor(s)
Page 29 and 30: Section 4 Configuration After the O
Page 31 and 32: TOP 0 0 Stroke Mode Local Single St
Page 33 and 34: a) Go to the Auto Sets screen. This
Page 35 and 36: October 16, 2008 Manual Version 1.1
Page 37 and 38: e changed. The up and down arrow ke
Page 39 and 40: tolerance limits. To configure a pa
Page 43: NOTE: It is very important make as
Page 46 and 47: ) Each configured sub-system has a
Page 50 and 51: IMPORTANT! Automatic movement will
Page 52 and 53: eported on the top line after the a
Page 55 and 56: Section 6 Diagnostics - Fault and S
Page 57 and 58: Section 6.3 Counterbalance and Cush
Page 59 and 60: Sys not Detected The hardware neces
Page 61: Coarse/Inc Turn Count Out of Synch
Page 64 and 65: Set the Min. Pressure to 25. Per th
Page 66 and 67: Set the Tolerance to .004 in. Set t
Page 69 and 70: Appendix B Typical Wiring Diagrams
Page 71 and 72: Figure B.3 Conceptual Dual Resolver
Page 73 and 74:
Figure B.5 Typical Slide Motor Star
Page 75 and 76:
Appendix C Lockout Procedure For Ai
Page 77:
Appendix D Specifications Section D
show all

OmniLink II Press Automation Control Automatic ... - LINK Systems

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?