3-18 Operating Manual

More documents

Recommendations

Info

Part No. Description Further accessories 16018 Rubber adapter for 15 ml glass tube 15022, suitable for 12150, 12156 16019 Rubber adapter for 15 ml glass tube 15022, suitable for 12155, 12159 16030 Rubber adapter for 30 ml glass tube 15033, suitable for 12150, 12156 16031 Rubber adapter for 30 ml glass tube 15033, suitable for 12155, 12159 16906 Rubber plate for 18025 16907 ditto, for 18050 16908 ditto, for 18100 16909 Rubber plate for rectangular carriers 18005, 18007, 18015 16910 Rubber plate for round carriers 17006, 17007, 17012, 17015, 17025 16911 Rubber plate for round carriers 17050, 17100 17112 Rectangular sealing cap, polysulfone, clear, incl. 2 clips 17118, for 13180 17111 Round sealing cap, polysulfone, clear, for 13104 16251 Sealing ring 58 x 3 mm for 13104 17190 Round sealing cap, polysulfone, clear, for 13190 17919 Table for centrifuge made of sheet-steel, varnished, with 2 doors and space for accessories, movable on lockable castors, dimensions: w 490, d 635, h 490 mm 17913 Fasteners for table 17919 Further accessories are available on request. Operating Manual SIGMA 3-18, page 28 of 95 03/06
Maximum speed for tubes Some tubes, e.g. glass tubes, microtubes, culture tubes, Teflon tubes and especially high volume tubes can be used in our rotors, buckets and adapters at speeds exceeding their breaking limit. We recommend to always fill up the tubes and to follow the recommendations of the manufacturer. Operating Manual SIGMA 3-18, page 29 of 95 03/06
Page 1: ———————————
Page 5: Konformitätserklärung (73/23/EWG;
Page 8 and 9: Operating Elements 4.1 Operating pa
Page 11: 1.1 Technical Data Manufactuer: S I
Page 14 and 15: Part No. Description 18009 Rectangu
Page 16 and 17: Part No. Description 11181 Swing-ou
Page 18 and 19: Part No. Description 17347 Round ca
Page 20 and 21: Part No. Description 17050 Round ca
Page 22 and 23: Part No. Description 12112 Angle ro
Page 24 and 25: Part No. Description 15040 Reaction
Page 26 and 27: Part No. Description 15074 Polycarb
Page 30 and 31: Operating Manual SIGMA 3-18, page 3
Page 32 and 33: 1.5 Safety Instructions According t
Page 34 and 35: 2.1 General Outlay The new generati
Page 36 and 37: 2.6.3 Rotor Monitoring During progr
Page 38 and 39: 3.2 Installation 3.2.1 Site All ene
Page 40 and 41: 12. Rotors with lid should always b
Page 42 and 43: 3.4 Initial Start-Up Attention! Bef
Page 44 and 45: 4.1.1 Start-key This key can be use
Page 46 and 47: 4.2 Display 4.2.1 Set 4.2.2 Speed D
Page 48 and 49: 4.2.5 Program (PROG) Program In thi
Page 50 and 51: 4.2.7.1 Acceleration Acceleration T
Page 52 and 53: 4.2.8 Configuration Configuration S
Page 54 and 55: 5.1.1 Selection and Alteration of t
Page 56 and 57: 5.1.2 Selection and Alteration of t
Page 58 and 59: 5.1.4 Alteration of the Configurati
Page 60 and 61: • Select "SCREEN" by turning the
Page 62 and 63: 5.1.4.2 Creation of Curves for Vari
Page 64 and 65: • Change the speed value by turni
Page 66 and 67: • Select “SPEED” by turning t
Page 68 and 69: 6.1 Load, Save and Delete Programs
Page 70 and 71: 6.1.2 Save a Program If you want to
Page 72 and 73: 7.1 Practical Notes for Centrifugat
Page 74 and 75: 7.2 Forbidden Centrifuging Operatio
Page 76 and 77: 8.1 Care and Cleaning of Centrifuge
Page 78 and 79:
8.5 Sterilization and Disinfection
Page 80 and 81:
8.6 Checks by Operator The operator
Page 82 and 83:
The curve 9 is a special case compa
Page 84 and 85:
9.3 Entry Limitations Valid entries
Page 86 and 87:
9.5.4 Emergency Lid Release In the
Page 89:
-----------------------------------
Page 93:
9.9 Program No.: Used for .........
show all

3-18 Operating Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?