3-18 Operating Manual

More documents

Recommendations

Info

Thank you very much for your confidence in the products of our company. Our centrifuges are manufactured carefully according to the highest quality standards and we are sure that your demands will always be fulfilled. Please read this manual carefully before installation of the centrifuge to ensure a proper and safe operation. We are wishing you a successful use of the centrifuge. SIGMA Laborzentrifugen GmbH P.O. Box 1713 - 37507 Osterode/Germany Phone 05522/5007-0 - Fax 05522/500712 Internet: www.sigma-zentrifugen.de eMail: info@sigma-zentrifugen.de SIGMA Service-Tel. 05522/5007-25 Operating Manual SIGMA 3-18, page 3 of 95 03/06
Page 1: ———————————
Page 7 and 8: General Information 1.1 Technical d
Page 9: Notes for Centrifugation 7.1 Practi
Page 13 and 14: 1.2 Accessories Suitable for SIGMA
Page 15 and 16: Part No. Description 18051 Rectangu
Page 17 and 18: Part No. Description 17358 Round ca
Page 19 and 20: Part No. Description 17007 Round ca
Page 21 and 22: Part No. Description 14002 Casset f
Page 23 and 24: Part No. Description 13080 Adapter
Page 25 and 26: Part No. Description 15030 Polycarb
Page 27 and 28: Part No. Description 15248 Polycarb
Page 29 and 30: Maximum speed for tubes Some tubes,
Page 31 and 32: 1.3 Scope of Supply The following b
Page 33 and 34: 1.6 Symbol Table International symb
Page 35 and 36: 2.5 Electronic Control The electron
Page 37 and 38: 3.1 Unpacking of the Centrifuge Ope
Page 39 and 40: 3.3 Installation of Rotors and Acce
Page 41 and 42: Operating Manual SIGMA 3-18, page 4
Page 43 and 44: 4.1 Operating Panel Operating panel
Page 45 and 46: 4.1.4 Knob This knob can be used fo
Page 47 and 48: 4.2.4 Time Time The set run time is
Page 49 and 50: 4.2.6 Rotor (here: 11180/13180) Rot
Page 51 and 52: 4.2.7.4 Density Density If the dens
Page 53 and 54:
5.1 Selection, Display and Alterati
Page 55 and 56:
Activation of the start delay and/o
Page 57 and 58:
5.1.3 Alteration of Program Paramet
Page 59 and 60:
• INFO: The Info menu displays in
Page 61 and 62:
5.1.4.1 Curves • By pressing the
Page 63 and 64:
• Select “0:00:00” by turning
Page 65 and 66:
• Activate the speed value “0
Page 67 and 68:
5.1.5 Alteration of the Contrast If
Page 69 and 70:
2. Loading from the list of program
Page 71 and 72:
6.1.3 Delete a Program If you want
Page 73 and 74:
11. Please pay attention to the max
Page 75 and 76:
16. Attention: Do not open cover an
Page 77 and 78:
8.3 Rotor Pins/Motorized Lid Lock
Page 79 and 80:
8.5.1 Autoclaving The life of the a
Page 81 and 82:
9.1 Slope of Specified Curves, Line
Page 83 and 84:
9.2 Quadratic Curves − The decele
Page 85 and 86:
9.5 Error Correction Most of the er
Page 87:
9.6 Error Codes Error no. Kind of e
Page 91:
-----------------------------------
Page 95:
Operating Manual SIGMA 3-18, page 9
show all

3-18 Operating Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?