3-18 Operating Manual

More documents

Recommendations

Info

3.4 Initial Start-Up Attention! Before initial start-up please take care that your centrifuge is orderly installed (refer to chapter 3.2 "Installation"). 3.4.1 Switching on of the Centrifuge Press mains switch (right side panel). When power is applied the first time, default values will be displayed: − The command panel illuminates. − The speed display indicates "2000". − The time display indicates "2“. − The program display indicates "--", i.e. 3.4.2 Opening Lid - the centrifuge will accelerate to 2000 rpm, - the centrifuge operation is terminated after 2 minutes, - no program number has been allocated so far. Press Lid-key − The lid opens. 3.4.3 Installation of a Rotor Put a rotor onto the shaft and fasten it by screwing the rotor tie-down screw clockwise onto the drive shaft. Please use the supplied rotor wrench (refer to chapter 3.3 "Installation of rotor and accessories"). Please pay attention to the fact that during tightening the disc spring of the rotor tie-down screw is pressed together and the screw is tightened. Operating Manual SIGMA 3-18, page 42 of 95 03/06
4.1 Operating Panel Operating panel The centrifuge can be operated via the operating panel. Keys can be pressed when their LED is on. Operating Manual SIGMA 3-18, page 43 of 95 03/06
Page 1: ———————————
Page 5: Konformitätserklärung (73/23/EWG;
Page 8 and 9: Operating Elements 4.1 Operating pa
Page 11: 1.1 Technical Data Manufactuer: S I
Page 14 and 15: Part No. Description 18009 Rectangu
Page 16 and 17: Part No. Description 11181 Swing-ou
Page 18 and 19: Part No. Description 17347 Round ca
Page 20 and 21: Part No. Description 17050 Round ca
Page 22 and 23: Part No. Description 12112 Angle ro
Page 24 and 25: Part No. Description 15040 Reaction
Page 26 and 27: Part No. Description 15074 Polycarb
Page 28 and 29: Part No. Description Further access
Page 30 and 31: Operating Manual SIGMA 3-18, page 3
Page 32 and 33: 1.5 Safety Instructions According t
Page 34 and 35: 2.1 General Outlay The new generati
Page 36 and 37: 2.6.3 Rotor Monitoring During progr
Page 38 and 39: 3.2 Installation 3.2.1 Site All ene
Page 40 and 41: 12. Rotors with lid should always b
Page 44 and 45: 4.1.1 Start-key This key can be use
Page 46 and 47: 4.2 Display 4.2.1 Set 4.2.2 Speed D
Page 48 and 49: 4.2.5 Program (PROG) Program In thi
Page 50 and 51: 4.2.7.1 Acceleration Acceleration T
Page 52 and 53: 4.2.8 Configuration Configuration S
Page 54 and 55: 5.1.1 Selection and Alteration of t
Page 56 and 57: 5.1.2 Selection and Alteration of t
Page 58 and 59: 5.1.4 Alteration of the Configurati
Page 60 and 61: • Select "SCREEN" by turning the
Page 62 and 63: 5.1.4.2 Creation of Curves for Vari
Page 64 and 65: • Change the speed value by turni
Page 66 and 67: • Select “SPEED” by turning t
Page 68 and 69: 6.1 Load, Save and Delete Programs
Page 70 and 71: 6.1.2 Save a Program If you want to
Page 72 and 73: 7.1 Practical Notes for Centrifugat
Page 74 and 75: 7.2 Forbidden Centrifuging Operatio
Page 76 and 77: 8.1 Care and Cleaning of Centrifuge
Page 78 and 79: 8.5 Sterilization and Disinfection
Page 80 and 81: 8.6 Checks by Operator The operator
Page 82 and 83: The curve 9 is a special case compa
Page 84 and 85: 9.3 Entry Limitations Valid entries
Page 86 and 87: 9.5.4 Emergency Lid Release In the
Page 89: -----------------------------------
Page 93:
9.9 Program No.: Used for .........
show all

3-18 Operating Manual

Create successful ePaper yourself

Delete template?

Save as template?