Users Manual - Warranty Life

More documents

Recommendations

Info

Chapter 4 Customizing the Scanner You can customize the scanner by modifying communications, bar code type, and other scanner parameters with the bar-coded parameter menu or the configuration software ScannerSetting*. These parameters retain their settings even when the power is off. (1) Scanning parameter setting bar codes from the bar-coded parameter menu by pressing the trigger switch. (The bar-coded parameter menu is given in Chapter 12.) (2) Using the configuration software (ScannerSetting)* in your computer. (The software also offers batch-process bar code printouts for read by scanners in the field.) * Registered users can download the configuration software (ScannerSetting) from QBdirect, their customer support section on the Denso Wave website at no extra charge. For further details on QBdirect or to register, visit the following URL. http://www.qbdirect.net 7
Chapter 5 Scanning Control Two types of scanning controls are available--Trigger switch control and Software control. Trigger switch control: Pressing the trigger switch readies the scanner for scanning. Software control: Instead of pressing the trigger switch, you send control commands from the host computer via the RS-232C interface to ready the scanner for scanning or put the scanner on standby. 5.1 Trigger Switch Control Pressing the trigger switch turns on the illumination LED and readies the scanner for scanning. The scanner supports the following five trigger switch operating modes. Select the one that best meets your needs using the bar-coded parameter menu or the configuration software (ScannerSetting). (1) Auto-off mode 1 Holding down the trigger switch lights the illumination LED for the specified period (selectable from 1 to 5 seconds in one second increments with the configuration software (ScannerSetting)), during which the scanner is ready to scan. When a bar code is read successfully or the specified period has elapsed, the illumination LED goes off and the scanner switches to standby. (2) Auto-off mode 2 If you press the trigger switch, the illumination LED lights for approx. 5 seconds during which the scanner is ready to scan, regardless of whether a bar code is read successfully or the trigger switch is released. After a bar code is read successfully, the ready-to-scan state further continues for approx. 5 seconds. If the scanner is left without scanning operation for approx. 5 seconds, it turns off the illumination LED and switches to standby. (3) Momentary switching mode 1 (Factory default) Only while you hold down the trigger switch, the illumination LED lights and the scanner is ready to scan. When you release the trigger switch or a bar code is read successfully, the illumination LED goes off and the scanner switches to standby. (4) Momentary switching mode 2 Only while you hold down the trigger switch, the illumination LED lights and the scanner is ready to scan, regardless of whether a bar code is read successfully. When you release the trigger switch, the illumination LED goes off and the scanner switches to standby. (5) Continuous reading mode When you turn the scanner on, the scanner lights the illumination LED and becomes ready to scan. The scanner ignores all trigger switch input. Note: When you are setting parameters using the bar-coded parameter menu, the scanner is always in the momentary switching mode 1 regardless of the trigger switch operating mode selected. Note: The trigger switch is disabled as long as the scan lock (see Section 7.1.3) is in effect in the data verification mode. 8
Page 1 and 2: Bar Code Handy Scanner GT10B-SM / G
Page 3 and 4: Contents Preface ..................
Page 5 and 6: Preface This user's manual sets for
Page 7 and 8: To System Designers: • When intro
Page 9 and 10: • When disconnecting the AC adapt
Page 11 and 12: Chapter 2 Preparation 2.1 Connectin
Page 13 and 14: Using the PS/2 keyboard interface N
Page 15: Reading RSS-14 Stacked and RSS-14 S
Page 19 and 20: Failure read • Auto-off mode 1 Co
Page 21 and 22: Chapter 6 Magic Key Control The mag
Page 23 and 24: Chapter 7 Scanning Functions 7.1 Da
Page 25 and 26: 7.1.2 Verification conditions You c
Page 27 and 28: 7.2 Specifying the Numbers of Digit
Page 29 and 30: (3) Extracting data from the specif
Page 31 and 32: 8.4 Parenthesizing AIs (Application
Page 33 and 34: (12) Conversions apply to Codabar s
Page 35 and 36: AI Format Description 345n n4+n6 Wi
Page 37 and 38: AI Format Description 94 N2+an..30
Page 39 and 40: One-shot beep* 2 (40 ms) or intermi
Page 41 and 42: 9.3 Vibrator The bar-coded paramete
Page 43 and 44: 10.2 PS/2 Keyboard Interface This I
Page 45 and 46: (4) Number of digits This optional
Page 47 and 48: 10.3.2 GTIN Format Conversion If th
Page 49 and 50: (3) PS/2 keyboard interface The fol
Page 51 and 52: Terminator Items Parameters Default
Page 53 and 54: UPC-A/E, EAN-13/8 Items Parameters
Page 55 and 56: Item Parameters Defaults Refer to:
Page 57 and 58: (5) Trigger switch control and magi
Page 59 and 60: (7) Data verification mode Items Pa
Page 61 and 62: Chapter 12 Bar-Coded Parameter Menu
Page 63 and 64: Communications parameters for the R
Page 65 and 66: Communications parameters for the P
Page 67 and 68:
Header (PS/2 keyboard interface) No
Page 69 and 70:
Data transmission interval (PS/2 ke
Page 71 and 72:
Scanning UPC-A, UPC-E, EAN-13 and E
Page 73 and 74:
Transmission format of EAN-8 (Conve
Page 75 and 76:
Scanning Codabar (NW-7) Enable, wit
Page 77 and 78:
Scanning Code 39 Enable, without C/
Page 79 and 80:
RSS Scanning RSS-14, RSS-14 Truncat
Page 81 and 82:
Scanner sensibility level in auto s
Page 83 and 84:
Verification result output in data
Page 85 and 86:
Chapter 13 Troubleshooting Problem
Page 87 and 88:
Reading diagrams GT10B-SM/GT11B-SM
Page 89 and 90:
Appendix 2 Bar Code Sample Label 03
Page 91 and 92:
Bar Code Handy Scanner GT10B-SM / G
show all

Users Manual - Warranty Life

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?