Users Manual - Warranty Life

More documents

Recommendations

Info

SAFETY PRECAUTIONS Be sure to observe all these safety precautions. Please READ through these instructions carefully. They will enable you to use the scanner correctly. Always keep this manual nearby for speedy reference. Strict observance of these warnings and cautions is a MUST for preventing accidents that could result in bodily injury and substantial property damage. Make sure you fully understand all definitions of these terms and symbols given below before you proceed to the text itself. Alerts you to those conditions that could cause serious bodily injury or death if the instructions are not followed correctly. Alerts you to those conditions that could cause minor bodily injury or substantial property damage if the instructions are not followed correctly. Meaning of Symbols A triangle ( ) with a picture inside alerts you to a warning of danger. Here you see the warning for electrical shock. A diagonal line through a circle ( ) warns you of something you should not do; it may or may not have a picture inside. Here you see a screwdriver inside the circle, meaning that you should not disassemble. A black circle ( ) with a picture inside alerts you to something you MUST do. This example shows that you MUST unplug the power cord. ii
To System Designers: • When introducing the scanner in those systems that could affect human lives (e.g., medicines management system), develop applications carefully through redundancy and safety design which avoids the feasibility of affecting human lives even if a data error occurs. • Keep the AC adapter from water. Failure to do so could cause fire or electrical shock. • Use the dedicated AC adapter only. Failure to do so could result in fire. • If the power cord of the AC adapter is damaged (e.g., exposed or broken lead wires), stop using it and contact your nearest dealer. Failure to do so could result in a fire or electrical shock. • Never bring any metals into contact with the terminals in connectors. Doing so could produce a large current through the scanner, resulting in heat or fire, as well as damage to the scanner. • Never use the scanner on the line voltage other than the specified level. Doing so could cause the scanner to break or burn. • Do not use the scanner where any inflammable gases may be emitted. Doing so could cause fire. • Do not scratch, modify, bend, twist, pull, or heat the power cable of the AC adapter. Do not place heavy material on the cable or allow the cable to get pressed under heavy material. Doing so could break the cable, resulting in a fire. • Do not subject the scanning window of the scanner to direct sunlight for extended periods. Doing so could damage the scanner, resulting in a fire. • If smoke, abnormal odors or noises come from the scanner, immediately switch off the host computer, disconnect the AC adapter and the interface cable, and contact your nearest dealer. Failure to do so could cause fire or electrical shock. • If foreign material or water gets into the scanner, immediately unplug the AC adapter and the interface cable, and contact your nearest dealer. Failure to do so could cause fire or electrical shock. • If you drop the scanner so as to affect the operation or damage its housing, switch off the host computer, unplug the AC adapter and the interface cable, and contact your nearest dealer. Failure to do so could cause fire or electrical shock. iii
Page 1 and 2: Bar Code Handy Scanner GT10B-SM / G
Page 3 and 4: Contents Preface ..................
Page 5: Preface This user's manual sets for
Page 9 and 10: • When disconnecting the AC adapt
Page 11 and 12: Chapter 2 Preparation 2.1 Connectin
Page 13 and 14: Using the PS/2 keyboard interface N
Page 15 and 16: Reading RSS-14 Stacked and RSS-14 S
Page 17 and 18: Chapter 5 Scanning Control Two type
Page 19 and 20: Failure read • Auto-off mode 1 Co
Page 21 and 22: Chapter 6 Magic Key Control The mag
Page 23 and 24: Chapter 7 Scanning Functions 7.1 Da
Page 25 and 26: 7.1.2 Verification conditions You c
Page 27 and 28: 7.2 Specifying the Numbers of Digit
Page 29 and 30: (3) Extracting data from the specif
Page 31 and 32: 8.4 Parenthesizing AIs (Application
Page 33 and 34: (12) Conversions apply to Codabar s
Page 35 and 36: AI Format Description 345n n4+n6 Wi
Page 37 and 38: AI Format Description 94 N2+an..30
Page 39 and 40: One-shot beep* 2 (40 ms) or intermi
Page 41 and 42: 9.3 Vibrator The bar-coded paramete
Page 43 and 44: 10.2 PS/2 Keyboard Interface This I
Page 45 and 46: (4) Number of digits This optional
Page 47 and 48: 10.3.2 GTIN Format Conversion If th
Page 49 and 50: (3) PS/2 keyboard interface The fol
Page 51 and 52: Terminator Items Parameters Default
Page 53 and 54: UPC-A/E, EAN-13/8 Items Parameters
Page 55 and 56: Item Parameters Defaults Refer to:
Page 57 and 58:
(5) Trigger switch control and magi
Page 59 and 60:
(7) Data verification mode Items Pa
Page 61 and 62:
Chapter 12 Bar-Coded Parameter Menu
Page 63 and 64:
Communications parameters for the R
Page 65 and 66:
Communications parameters for the P
Page 67 and 68:
Header (PS/2 keyboard interface) No
Page 69 and 70:
Data transmission interval (PS/2 ke
Page 71 and 72:
Scanning UPC-A, UPC-E, EAN-13 and E
Page 73 and 74:
Transmission format of EAN-8 (Conve
Page 75 and 76:
Scanning Codabar (NW-7) Enable, wit
Page 77 and 78:
Scanning Code 39 Enable, without C/
Page 79 and 80:
RSS Scanning RSS-14, RSS-14 Truncat
Page 81 and 82:
Scanner sensibility level in auto s
Page 83 and 84:
Verification result output in data
Page 85 and 86:
Chapter 13 Troubleshooting Problem
Page 87 and 88:
Reading diagrams GT10B-SM/GT11B-SM
Page 89 and 90:
Appendix 2 Bar Code Sample Label 03
Page 91 and 92:
Bar Code Handy Scanner GT10B-SM / G
show all

Users Manual - Warranty Life

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?