CMN-91 Compact Video and Audio Monitor ... - Biznine.com

More documents

Recommendations

Info

Section 3 ♦ General Information • Menu Settings: Shortcut menus within a function that are used to control the parameters for the individual function. • Global Setup Menu Settings: Setup menu parameters that affect the entire unit (not function-specific). The Setup menu is accessed by pressing the SETUP button. Front Panel Controls The front panel controls are illustrated in Figure 3-2. Figure 3-2. CMN-91 Front Panel Controls Most buttons and text are in a low-tally (low illumination) state; under certain conditions, however, some buttons and text reach a high-tally (high illumination) state, as described in Table 3-1. If a function is not operational, the associated button illumination is OFF. The high and low tally illumination levels can be set in the High Tally and Low Tally selection options of the Unit Configuration → Front Panel setup menu selection option.. NOTE: Multiple buttons may be high tally at the same time. The last control selected is the active control. Table 3-1. CMN-91 Front Panel Controls Key Label Description 1 POWER • Power switch button; press and release to turn unit power on • Press and hold to turn unit power off 2 A/B SDI input button, press to toggle between SDI input A and B 3 DISP • Display button; press and release to freeze a display • Once a display is frozen, press and release to toggle between live and frozen mode 4 MLT • Multi-display or Overlay button; press and release to toggle between a full-display and a multi-display screen • Press and hold to access the MLT Setup menu 20 CMN-91 Series Installation and Operation Handbook Copyright © 2009, Harris Corporation
Table 3-1. CMN-91 Front Panel Controls Section 3 ♦ General Information Key Label Description 5 SDI • Data button; press and release to freeze data • Once data is frozen, press and release to toggle between live and frozen mode 6 REF External Reference selection button; press and release to toggle between internal and external reference 7 CLEAR • Clear Display selection button; press and release to clear a display • Press and hold to access the Clear Setup menu 8 H/V Horizontal/vertical sweep selection button; press and release to toggle between waveform horizontal and vertical sweep 9 COMP Component selection button; press and release to cycle through individual waveform components 10 ZOOM Zoom selection button; press and release for zoom selections 11 USB port 12 Headphone jack 13 VOL • Volume selection button; press and release to activate the curved knob to adjust headphone audio volume • Press and hold to access the audio channel selection matrix 14 WFM • Waveform selection button; press and release for a waveform display • Press and hold to access the Waveform Setup menu 15 VEC • Vector selection button; press and release for a vector display • Press and hold to access the Vector Setup menu 16 GMT • Gamut selection button; press and release for a gamut display • Press and hold to access the Gamut Setup menu 17 PICT • Picture selection button; press and release for a picture display • Press and hold to access the Picture Setup menu 18 PIP • Picture-in-picture selection button; press and release for a thumbnail display of the current picture available with the selected input 19 AUD • Audio selection button; press and release for an audio display • Press and hold to access the Audio Setup menu 20 ALRM • Alarm selection button; press and release to switch to Alarm mode • Press and hold to access the Alarm Setup menus 21 TIME • Timing selection button; press and release to switch to Timing mode • Press and hold to access the Timing Setup menu 22 OPT • Option selection button; press and release for the LTC or REF waveform displays • Press and hold to access the OPT menu 23 EXIT Exit selection button; press and release to leave menu function selections 24 Navigation Use to navigate menus and select selection options (see page 21 for an explanation of how to operate the navigation items) 25 SETUP • Setup button; press and release to access Setup mode • Press and release to exit the displayed Setup menu 26 VIEW View Adjust selection button; press and release to enable controls to scale or adjust the position of an active display 27 Left/Right Arrow Knob Use to move the waveform display 28 POS Position selection button; press and release to enable controls to horizontally or vertically adjust the contents of a WFM, LTC, or REF waveform display CMN-91 Series Installation and Operation Handbook 21 Copyright © 2009, Harris Corporation
Page 1: CMN-91 Compact Video and Audio Moni
Page 4 and 5: Ensuring Safety Operator’s Safety
Page 6 and 7: Operator’s Safety Summary This pa
Page 8 and 9: Directives and Compliances In accor
Page 10 and 11: Contents Selecting an Input .......
Page 12 and 13: Contents Video Setup Menu Selection
Page 14 and 15: Contents GNU Lesser Public License
Page 16 and 17: Contents Table 1-6. SD Formats ....
Page 18 and 19: Contents This page is intentionally
Page 20 and 21: Section 1 ♦ Introduction • XGA,
Page 22 and 23: Table 1-4. Dual Link Formats Sectio
Page 24 and 25: Service and Support Section 1 ♦ I
Page 26 and 27: Section 2 ♦ Installation Installi
Page 28 and 29: Section 2 ♦ Installation Table 2-
Page 30 and 31: Section 2 ♦ Installation Table 2-
Page 32 and 33: Connecting the CMN-91 Section 2 ♦
Page 34 and 35: Section 2 ♦ Installation • For
Page 36 and 37: Section 2 ♦ Installation This pag
Page 40 and 41: Table 3-1. CMN-91 Front Panel Contr
Page 42 and 43: Figure 3-4. Overlay Display Table 3
Page 44 and 45: Section 3 ♦ General Information A
Page 46 and 47: Recalling Captured Data Section 3
Page 48 and 49: Figure 4-1. Waveform Display Diagra
Page 50 and 51: Section 4 ♦ Operating the CMN-91
Page 52 and 53: Figure 4-6. Establishing the Gain S
Page 56 and 57: Figure 4-11. Vector NTSC Zoom Upper
Page 58 and 59: Figure 4-15. Vector PAL Zoom Center
Page 60 and 61: Figure 4-18. Establishing the Vecto
Page 68 and 69: Picture Display Section 4 ♦ Opera
Page 70 and 71: PIP Display Section 4 ♦ Operating
Page 74 and 75: Figure 4-31. Six Bar Graph Display
Page 76 and 77: Figure 4-33. Sixteen Bar Graph Disp
Page 84 and 85: Figure 4-37. LTC Display Diagram Se
Page 86 and 87: Section 5 ♦ Global Setup Menu Fun
Page 88 and 89:
Section 5 ♦ Global Setup Menu Fun
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Section 6 ♦ Alarm Descriptions Ta
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Section 6 ♦ Alarm Descriptions Au
Page 122 and 123:
Section 6 ♦ Alarm Descriptions Wh
Page 124 and 125:
Section 8 ♦ Troubleshooting This
Page 126 and 127:
Section 8 ♦ Troubleshooting Table
Page 128 and 129:
Appendix A ♦ Specifications Exter
Page 130 and 131:
Appendix A ♦ Specifications Wavef
Page 132 and 133:
Environmental Item Specification Op
Page 134 and 135:
Appendix B ♦ Pinouts Figure B-2.
Page 136 and 137:
Appendix B ♦ Pinouts This page is
Page 138 and 139:
Appendix C ♦ Open Source Software
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
The GNU v2 License Appendix C ♦ O
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Appendix D ♦ Glossary Baseband Vi
Page 160 and 161:
Appendix D ♦ Glossary Editor A de
Page 162 and 163:
Appendix D ♦ Glossary High Defini
Page 164 and 165:
Appendix D ♦ Glossary NTSC Nation
Page 166 and 167:
Appendix D ♦ Glossary Segment Err
Page 168 and 169:
Appendix D ♦ Glossary This page i
Page 170 and 171:
DRC-2A rackmount, 11 DRC-3 rackmoun
Page 172:
SD-SDI, 109, 110 time code, 112 Sta
show all

CMN-91 Compact Video and Audio Monitor ... - Biznine.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?