Operator's Manual 10 in. COMPOUND MITER SAW WITH ... - Sears

More documents

Recommendations

Info

KNOW YOUR COMPOUND MITER SAW Cover Plate Hold-down Clamp Table Miter Scale Upper Plate Guard Dust Bag Bevel Scale Left Extension Wing Safety Lock-Off Button ON/OFF Trigger Switch Arbor Lock Laser Guide Fence Table Insert Hand Hold for Transportation Extension Wing Locking Screw Miter Angle Pointer 10 Motor Lower Blade Guard Switch Handle Hand Hold for Transportation Base Positive Stop Locking Lever Miter Lock Handle Right Extension Wing Laser On/Off Switch Hold-down Latch Bevel Lock Handle Rear Extension Stay
COMPOUND MITER SAW TERMS ARBOR LOCK – Allows the user to keep the blade from rotating while tightening or loosening the arbor bolt during blade replacement or removal. BASE – Supports the table, holds accessories and allows for workbench or leg set mounting. BEVEL LOCKING HANDLE – Locks the miter saw at a desired bevel angle. BEVEL SCALE – To measure the bevel angle of the saw blade 0° to 45° left. COVER PLATE SCREW – Loosen this screw and rotate the plate for access to the blade arbor bolt. FENCE – Helps to keep the workpiece from moving when sawing. Scaled to assist with accurate cutting. LOWER BLADE GUARD – Helps protect your hands from the blade in the raised position, it retracts as the blade is lowered. MITER HANDLE – Used to rotate the table, and to rotate the saw to a right or left cutting position. MITER SCALE – Measures the miter angle 0° to 45° left and right. MOUNTING HOLES – To mount the miter saw to a stable surface. ON/OFF TRIGGER SWITCH – To start the tool, squeeze the trigger. Release the trigger to turn off the miter saw. POSITIVE STOP LOCKING LEVER – Locks the miter saw at a preset positive stop for the desired miter angle. STOP LATCH – Locks the miter saw in the lowered position for compact storage and transportation. SWITCH HANDLE – The switch handle contains the trigger switch and the laser on/off switch. The blade is lowered into the workpiece by pushing down on the handle. The saw will return to its upright position when the handle is released. WARNING LABELS – Read and understand for your own safety. Make sure all labels are present GLOSSARY OF TERMS 11 on machine and legible. WRENCH STORAGE – Convenient storage to prevent misplacing the blade wrench. WOODWORKING TERMS ARBOR – The shaft on which a blade is mounted. BEVEL CUT – An angle cut made through the face of the workpiece. COMPOUND CUT – A simultaneous bevel and miter cut. CROSS CUT – A cut made across the width of the workpiece. FREEHAND – Performing a cut without using a fence (guide), hold down or other proper device to prevent the workpiece from twisting during the cutting operation. GUM – A sticky sap from wood products. HEEL – Misalignment of the blade. KERF – The amount of material removed by blade cut. MITER CUT – An angle cut made across the width of the workpiece. RESIN – A sticky sap that has hardened. REVOLUTIONS PER MINUTE (RPM) – The number of turns completed by a spinning object in one minute. SAW BLADE PATH – The area of the workpiece or table top directly in line with the travel of the blade or the part of the workpiece which will be cut. SET – The distance between two saw blade tips, bent outward in opposite directions to each other. The further apart the tips are, the greater the set. WORKPIECE – The item being cut. The surfaces of a workpiece are commonly referred to as faces, ends and edges.
Page 2 and 3: TABLE OF CONTENTS SECTION PAGE SECT
Page 4 and 5: GENERAL SAFETY INSTRUCTIONS BEFORE
Page 6 and 7: COMPOUND MITER SAW SAFETY SPECIFIC
Page 8 and 9: ACCESSORIES AND ATTACHMENTS TOOLS N
Page 12 and 13: ASSEMBLY AND ADJUSTMENTS ASSEMBLY I
Page 14 and 15: TO INSTALL THE REAR EXTENSION STAY
Page 16 and 17: ADJUSTMENT INSTRUCTIONS ! WARNING T
Page 18 and 19: Mounting instructions 1. For statio
Page 20 and 21: PLAN YOUR WORK ● Use the right to
Page 22 and 23: MITER CUT (FIG. W) 1. When a miter
Page 24 and 25: MAINTENANCE ! DANGER To avoid injur
Page 26 and 27: 10 in. COMPOUND MITER SAW MODEL NO.
Page 28 and 29: 10 in. COMPOUND MITER SAW MODEL NO.
Page 30 and 31: REPAIR PROTECTION AGREEMENTS Congra

Operator's Manual 10 in. COMPOUND MITER SAW WITH ... - Sears

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?