Spicer Tandem Drive Axles Service Manual

More documents

Recommendations

Info

37 6. Remove the bearing cones from the plain and flange halves in two steps: a. Mount the puller vertically to split the bearing. This action will start the bearing moving off the differential case. b. Mount the puller horizontally to remove the cone. Wheel Differential
Wheel Differential Assembly IMPORTANT To prevent bearing damage, use suitable sleeve that only contacts the inner race of the cone. A used bearing race would be a suitable tool. This tool should have a slit cut if the ID is the same as the flange OD. 1. Press the new bearing cone on the plain half and flange half bearing boss using the proper press sleeve or bearing installation tool. 2. Place the plain half side of the differential case on a malleable surface. 3. Install the side gear. Apply a thin coat of oil to the mating surfaces of the side gear and plain half. Wheel Differential 4. Assemble the side pinions onto the wheel differential spider. Apply a thin coat of oil to the mating surfaces of the side pinion and differential spider. Install the wheel differential nest on top of the side gear. 5. Install the flange half side gear. Apply a thin coat of oil to the mating surfaces. 6. Install the ring gear. Align the capscrew holes. 1 1 - Match spacing of holes on each side of spider slots 38 Wheel Differential
Page 1 and 2: Spicer ® Tandem Drive Axles Servic
Page 3 and 4: General Inspection General Informat
Page 5 and 6: Introduction ......................
Page 7 and 8: Model Identification Drive Axle 1 -
Page 9 and 10: Failure Analysis Failure analysis i
Page 11 and 12: Inspection Clean 1. Wash steel part
Page 13 and 14: Differential Carrier Assembly - Par
Page 15 and 16: Differential Carrier Assembly Insta
Page 17 and 18: Power Divider - Parts Exploded View
Page 19 and 20: 10. Remove the thrust washer and he
Page 21 and 22: Lube Manifold Disassembly 1. Discon
Page 23 and 24: Pump Assembly Use these instruction
Page 25 and 26: Helical Gear Bushing Replacement: a
Page 27 and 28: 17. A. For axles built before Augus
Page 29 and 30: 6. Mount the differential carrier i
Page 31 and 32: Failure to de-stake the pinion nut
Page 33 and 34: Drive Pinion Drive Pinion Overhaul
Page 35 and 36: 5. For Forward Carriers Only: Insta
Page 37 and 38: 14. With 5 tons of force on the pre
Page 39 and 40: CAUTION The stake must be deep enou
Page 41: Wheel Differential Disassembly Duri
Page 45 and 46: Wheel Differential Assembly Set Bac
Page 47 and 48: 9. With a dial indicator, check the
Page 49 and 50: 21. When contact pattern is correct
Page 51 and 52: Adjust Ring Gear Position (Backlash
Page 53 and 54: Install and Adjust Wheel Differenti
Page 55 and 56: Remove Output Shaft Assembly Note:
Page 57 and 58: Output Shaft Assembly & Rear Cover
Page 59 and 60: Measure Correct endplay for a new a
Page 61 and 62: Guidelines for Reusing Yoke CAUTION
Page 63 and 64: Housing Breather Dana has an axle b
Page 65 and 66: Remove and Overhaul Wheel End Seal
Page 67 and 68: Never tighten the inner nut for ali
Page 69 and 70: Lubricate Wheel End CAUTION Before
Page 71 and 72: General Lubrication Information The
Page 73 and 74: Change Lube Drain Drain when the lu
Page 75 and 76: Tandem Rear Axles Installation Angl
Page 77 and 78: Theory of Operation Power Divider O
Page 79 and 80: Operate Wheel Differential Assembly
Page 81 and 82: Wheel Differential Lock The Dana Wh
Page 83 and 84: Power Divider - Parts Exploded View
Page 85 and 86: Parts Identification Rear Axle Pini
Page 87 and 88: Parts Identification Housing and Ou
Page 89 and 90: This page intentionally left blank.

Spicer Tandem Drive Axles Service Manual

Create successful ePaper yourself

Delete template?

Save as template?