CUTSKILL® C-35A - Victor Technologies

More documents

Recommendations

Info

GENERAL INFORMATION 1-6 Manual 0-4698
SECTION 2: INTRODUCTION General Information This Service Manual and parts list covers the CutSkill ® Model C-35A Plasma Cutting Power Supply. Do not use these instructions or parts on any other equipment. Provide the power supply model number and serial number when ordering parts. If a product must be returned for service, contact your distributor. Materials returned without proper authorization will not be accepted. Contact Information Thermal Dynamics Technical Service Dept. Tel: 1-800-752-7622 (1-800-PLASMA2) Fax: 1-800-221-4401 e-mail address: tdc-tech@thermadyne.com Replacement parts are shown on the following pages. Catalog numbers are shown below each part. 2.01 Overview Plasma is a gas which has been heated to an extremely high temperature and ionized so that it becomes electrically conductive. The plasma arc cutting process uses this plasma to transfer an electrical arc to the workpiece. The metal to be cut is melted by the heat of the arc and then blown away. 2.02 General Specifications System Descriptions C-35A Maximum Output 35 Amps 230V, Input Voltage & Phase Single Phase Frequency 50/60Hz Input Power 7.4 kVA Current Input Fuse 20 Amps No Load Voltage 330V Load Voltage 94V Output Current 15-35 Amps Post Flow Time 10 Seconds 75 psi (5.2 Operating Air Pressure bar)(.52 Mpa) 125 psi (8.6 bar) Maximum Air Pressure (.86 Mpa) 400 scfh Air Flow 6.6 scfm (188.7 lpm) System *Duty Cycle ratings at Ambient Air Temperatures 35% @ 35Amps of 40° C / 104° F. System *Duty Cycle ratings at Ambient Air Temperatures 60% @ 27Amps of 40° C / 104° F. System *Duty Cycle ratings 100% @ at Ambient Air Temperatures 20Amps of 40° C / 104° F. Maximum Cutting Capacity 1/2" (12mm) @ 35A 8.3"x20"x14.8" Dimension (W x D x H) (210 mm x 510 mm x 350 mm ) 44 lbs. Net Weight (20kg ) Manual 0-4698 2-1 Introduction
Page 1: C-35A CUTSKILL ® PLASMA CUTTING SY
Page 5 and 6: TABLE OF CONTENTS SECTION 1: GENERA
Page 7 and 8: SECTION 1: GENERAL INFORMATION 1.01
Page 9 and 10: THAT HAVE HELD HAZARDOUS SUBSTANCES
Page 11: 1.05 Statement of Warranty LIMITED
Page 15 and 16: 3.01 Site Selection SECTION 3: INST
Page 17 and 18: SECTION 4: OPERATION 4.01 Front Con
Page 19 and 20: E. Typical Cutting Speeds Cutting s
Page 21 and 22: 5.01 General Maintenance SECTION 5:
Page 23 and 24: SECTION 6: TROUBLESHOOTING WARNING
Page 25 and 26: 6.03 Control PCB Indicators 1. Turn
Page 27 and 28: A. Diode Testing Basics WARNING Dis
Page 29 and 30: B. Component Tests WARNING Disconne
Page 31 and 32: General Information SECTION 7: PART
Page 33 and 34: 21 26 22 11 16 17 15 12 24 Art # A-
Page 35 and 36: 5 6 4 1 3 7 Manual 0-4698 7-5 PARTS
Page 37 and 38: Appendix 1: Operating Sequence, Blo
Page 39 and 40: Appendix 3: Microchip Pin-Out CPU S
Page 41 and 42: No.40270601 AIR ERROR 218 VAC LD2 E
Page 43 and 44: No.40270601 AIR ERROR 218 VAC LD2 E
Page 45 and 46: GLOBAL CUSTOMER SERVICE CONTACT INF

CUTSKILL® C-35A - Victor Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?