Download complete product manual (PDF-File) - esd electronics, Inc.

More documents

Recommendations

Info

4.1.1 Default Setting of Jumpers Jumpers and Coding Switches The according default setting at board delivery is shown in the table below. For the position of jumpers please refer to figure 4.1.1. The jumpers will be shown below as seen by users with the board in front of them and the VMEbus connectors on the right. Default setting of jumpers: Jumper Function Default setting at board delivery SW120... SW123 basis address of board VME-DAC1612: $E20000 J120 address modifier decoding short/standard supervisory and nonprivileged accesses permitted J130 mode register depending on model and the output voltage range selected J300 output level after RESET (negation of data bit D11 for the D/A-converters) J400, J410, J420, J430, J500, J510, J520, J530, J600, J610, J620, J630, J700, J710, J720, J730 J401, J411, J421, J431, J501, J511, J521, J531, J601, J611, J621, J631, J701, J711, J721, J731 voltage swing of the D/Aconverter assigned bipolar/unipolar conversion of the D/A-converter assigned D11 is inverted, i.e. a bipolar operation has been selected U = 20 V - voltage range = ±10 V bipolar : ±5V, ±10V Table 4.1.1: Default setting of jumpers Manual VME-DAC1612 Rev. 1.1 9
Jumpers and Coding Switches 4.1.2 Setting Basis Address and Address Modifier Decoding 4.1.2.1 Basis Address (Coding Switch) 10 Address bits Setting via coding switches Default setting [Hex] Position A23...A20 SW120 E on board next to VMEbus connector P1 A19...A16 SW121 2 A15...A12 SW122 0 in front panel (above) A11...A8 SW123 0 in front panel (below) Table 4.1.2: Setting of basis address Manual VME-DAC1612 Rev. 1.1
Page 1 and 2: Manual VME-DAC1612 Rev. 1.1 VME-DAC
Page 3 and 4: Manual VME-DAC1612 Rev. 1.1 N O T E
Page 5 and 6: 2 7.3.6 Adjusting the Channels ....
Page 7 and 8: Technical Data 2. Summary of Techni
Page 9 and 10: Technical Data 2.3 Order Informatio
Page 11: Jumpers and Coding Switches 4. Jump
Page 15 and 16: Jumpers and Coding Switches 12 Jump
Page 17 and 18: Jumpers and Coding Switches 4.1.4 M
Page 19 and 20: Jumpers and Coding Switches 4.1.5 N
Page 21 and 22: Jumpers and Coding Switches configu
Page 23 and 24: Analog Outputs 5.2 Operating Modes
Page 25 and 26: Analog Outputs 5.2.2 Unipolar Opera
Page 27 and 28: Analog Outputs 5.2.4 Bipolar Operat
Page 29 and 30: Analog Outputs 5.3.1 Offset Setting
Page 31 and 32: Analog Outputs 28 This side is inte
Page 33 and 34: Software 6.2 PEARL-Example Program
Page 35 and 36: Appendix 7.1.2 I/O-Connector P2 and
Page 37 and 38: Appendix 7.1.3 Post Connectors P800
Page 39 and 40: Appendix 7.3 DAC812-Adapter (DAC812
Page 41 and 42: Appendix There are three combinatio
Page 43 and 44: Appendix 7.3.7 Assignment of Connec
Page 45 and 46: Appendix Signal descriptions to `Tr
Page 47 and 48: Appendix 7.3.7.3 Supplying the Anal

Download complete product manual (PDF-File) - esd electronics, Inc.

Create successful ePaper yourself

Delete template?

Save as template?