Control Units - Siemens

More documents

Recommendations

Info

Parameters List of Parameters p0346[0...2] Magnetization time / Magnetization time Access level: 3 P-Group: Motor Data type: FloatingPoint32 Quick comm. NO Active: YES Data set: DDS Can be changed: U, T Calculated: CALC_MOD_REG Min Max Factory setting 0.000 [s] 20.000 [s] 1.000 [s] Description: Sets magnetization time [s], i.e. waiting time between pulse enable and start of ramp-up. Motor magnetization builds up during this time. Magnetization time is normally calculated automatically from the motor data and corresponds to the rotor time constant. Notice: An excessive reduction of this time can result in insufficient motor magnetization. Note: If boost settings are higher than 100 %, magnetization time may be reduced. Default value is depending on inverter type and its rating data. p0347[0...2] Demagnetization time / Demagnet. time Access level: 3 P-Group: Motor Data type: FloatingPoint32 Quick comm. NO Active: YES Data set: DDS Can be changed: U, T Calculated: CALC_MOD_REG Min Max Factory setting 0.000 [s] 20.000 [s] 1.000 [s] Description: Changes time allowed after OFF2 / fault condition, before pulses can be re-enabled. Notice: Not active following a normally completed ramp-down, e.g. after OFF1, OFF3 or JOG. Overcurrent trips will occur if the time is decreased excessively. Note: The demagnetization time is approximately 2.5 x rotor time constant in seconds. Default value is depending on inverter type and its rating data. p0350[0...2] Stator resistance (line) / Stator res. (L) Access level: 3 P-Group: Motor Data type: FloatingPoint32 Quick comm. NO Active: YES Data set: DDS Can be changed: U, T Calculated: CALC_MOD_EQU Min Max Factory setting 0.00001 [Ohm] 2000.00000 [Ohm] 2.00000 [Ohm] Description: Stator resistance value in [Ohms] for connected motor (line value). The parameter value doesn't include the cable resistance. Note: There are three ways to determine the value for this parameter: 1. Calculate using - P0340 = 1 (data entered from rating plate) or - P0010 = 1, P3900 = 1, 2 or 3 (end of quick commissioning). 2. Measure using P1900 = 2 (standard motor data identification - value for stator resistance is overwritten). Measure using P1900 = 3 (compleate motor data identification - same like setting 2; additional detection of the saturation curve) 3. Measure manually using an Ohmmeter. Since the manually measured resistor is a line-to-line value, which includes the cable resistors, the measured value has to be divided by two and the cable resistor of a line has to be subtracted from that value. The value entered in P0350 (stator resistance) is the one obtained by the method last used. Default value is depending on inverter type and its rating data. 1-50 © Siemens AG 2008 All Rights Reserved SINAMICS G120 Control Units CU240E/S, Edition 07/2008
© Siemens AG 2008 All Rights Reserved SINAMICS G120 Control Units CU240E/S, Edition 07/2008 Parameters List of Parameters p0352[0...2] Cable resistance / Cable resistance Access level: 3 P-Group: Motor Data type: FloatingPoint32 Quick comm. NO Active: YES Data set: DDS Can be changed: U, T Calculated: CALC_MOD_EQU Min Max Factory setting 0.0 [Ohm] 120.0 [Ohm] 0.0 [Ohm] Description: Describes cable resistance between inverter and motor for one phase. The value corresponds to the resistance of the cable between the inverter and the motor, relative to the rated impedance. p0354[0...2] Rotor resistance / Rotor resistance Access level: 3 P-Group: Motor Data type: FloatingPoint32 Quick comm. NO Active: YES Data set: DDS Can be changed: U, T Calculated: CALC_MOD_EQU Min Max Factory setting 0.0 [Ohm] 300.0 [Ohm] 10.0 [Ohm] Description: Sets rotor resistance of motor equivalent circuit (phase value). Dependency: Calculated automatically using the motor model or determined using P1900 (motor identification). p0356[0...2] Stator leakage inductance / Stator leak.induct Access level: 3 P-Group: Motor Data type: FloatingPoint32 Quick comm. NO Active: YES Data set: DDS Can be changed: U, T Calculated: CALC_MOD_EQU Min Max Factory setting 0.00001 1000.00000 10.00000 Description: Sets stator leakage inductance [mH] of motor equivalent circuit (phase value). Dependency: Calculated automatically using the motor model or determined using P1900 (motor identification). p0358[0...2] Rotor leakage inductance / Rotor leak.induct. Access level: 3 P-Group: Motor Data type: FloatingPoint32 Quick comm. NO Active: YES Data set: DDS Can be changed: U, T Calculated: CALC_MOD_EQU Min Max Factory setting 0.0 1000.0 10.0 Description: Sets rotor leakage inductance [mH] of motor equivalent circuit (phase value). Dependency: Calculated automatically using the motor model or determined using P1900 (motor identification). p0360[0...2] Main inductance / Main inductance Access level: 3 P-Group: Motor Data type: FloatingPoint32 Quick comm. NO Active: YES Data set: DDS Can be changed: U, T Calculated: CALC_MOD_EQU Min Max Factory setting 0.0 10000.0 10.0 Description: Sets main inductance [mH] of the motor equivalent circuit (phase value). Dependency: Calculated automatically using the motor model or determined using P1900 (motor identification). Caution: The data of equivalent circuit relates to the star equivalent circuit. Any data of the delta equivalent circuit available, therefore must be transformed to the star equivalent circuit before entering into the inverter. 1-51
Page 1: Parameter Manual · Edition 07/2008
Page 4 and 5: Safety Guidelines Qualified Personn
Page 6 and 7: Contents Contents-6 © Siemens AG 2
Page 8 and 9: Parameters Introduction to Paramete
Page 14 and 15: Parameters List of Parameters p0003
Page 20 and 21: Parameters List of Parameters r0019
Page 28 and 29: Parameters List of Parameters Note:
Page 42 and 43: Parameters List of Parameters IEC M
Page 48 and 49: Parameters List of Parameters P0341
Page 100 and 101:
Parameters List of Parameters p0845
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Parameters List of Parameters r0949
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Parameters List of Parameters The f
Page 154 and 155:
Parameters List of Parameters ParNo
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Parameters List of Parameters Value
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Parameters List of Parameters If a
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Parameters Command and Drive Data S
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Parameters Connector/Binector (BICO
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
Parameters Quick commissioning (P00
Page 312 and 313:
Parameters Quick commissioning (P00
Page 314 and 315:
Function diagrams Contents: functio
Page 316 and 317:
Function diagrams Symbols in functi
Page 318 and 319:
Function diagrams Overview 2.3 Over
Page 320 and 321:
2-320 © Siemens AG 2008 All Rights
Page 322 and 323:
Page 324 and 325:
Page 326 and 327:
Page 328 and 329:
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Function diagrams Internal Setpoint
Page 338 and 339:
Page 340 and 341:
Page 342 and 343:
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Page 358 and 359:
Page 360 and 361:
Function diagrams Setpoint Channel
Page 362 and 363:
Page 364 and 365:
Page 366 and 367:
Function diagrams V/f Control 2.9 V
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
Page 374 and 375:
Page 376 and 377:
Page 378 and 379:
Page 380 and 381:
Page 382 and 383:
Function diagrams Vector Control 2-
Page 384 and 385:
Faults and Warnings Faults and Warn
Page 386 and 387:
Faults and Warnings List of Fault a
Page 388 and 389:
Page 390 and 391:
Page 392 and 393:
Page 394 and 395:
Page 396 and 397:
Page 398 and 399:
Page 400 and 401:
Page 402 and 403:
Page 404 and 405:
Page 406 and 407:
Page 408 and 409:
Page 410 and 411:
Page 412 and 413:
ASCII-Table A-412 © Siemens AG 200
Page 414 and 415:
List of Abbreviations Abbreviation
Page 416 and 417:
List of Abbreviations Abbreviation
Page 418 and 419:
Index 5100 PID Controller, 2-362 51
Page 420:
Index P Parameters Active, 1-10 Bin
show all

Control Units - Siemens

Create successful ePaper yourself

Delete template?

Save as template?