user´s manual fixturlaser xa geometry

More documents

Recommendations

Info

Straightness with the Arc Angle method 1. Place the laser transmitter as close as possible to the first bore. Make sure that the transmitter and its fixture is firmly attached to the casing. 2. Adjust the position of the laser, sideways and in height, until the laser beam is within 1-2 mm from the centre of the first reference bore, by using the tape measure. 3. Adjust the angle of the laser beam, horizontally and vertically, by using the micrometer screws on the laser transmitter to position it in the centre of the second reference bore. Use a tape measure to position the beam into the centre within 1-2 mm. Fixturlaser XA Geometry Manual 4.10
4. If necessary, repeat the procedure for coarse adjustment until the beam is centred in both reference bores. REPEATABILITY TEST Before starting the straightness measurement, we recommend that you perform a repeatability test. See chapter “Repeatability Test” in Fixturlaser XA <strong>manual</strong>. Do the repeatability test at a position far from the laser transmitter. Fixturlaser XA Geometry Manual 4.11
Page 1: FixtUrlaser xa GeoMetry User´s Man
Page 4 and 5: Fixturlaser XA Geometry Manual 3 rd
Page 6 and 7: Fixturlaser XA Geometry Manual 1.2
Page 8 and 9: Standard/Test report/Technical cons
Page 10 and 11: APPLICATION PROGRAMS Shaft Alignmen
Page 14 and 15: Straightness with the Arc Angle Met
Page 16 and 17: Best fit Angle format Notes Screen
Page 18 and 19: The selected area is marked in gree
Page 20 and 21: Straightness with the Clock method
Page 24 and 25: MEASUREMENT Summary screen The summ
Page 26 and 27: Measurement point registration - St
Page 28 and 29: Note A note with up to 20 character
Page 30 and 31: Live values are indicated with a bl
Page 32 and 33: Measurement point registration - St
Page 34 and 35: Minimum angle between positions is
Page 36 and 37: When the Arc Angle measurement is f
Page 38 and 39: MEASUREMENT RESULT Summary screen T
Page 40 and 41: List screen The list screen shows a
Page 42 and 43: ALIGNMENT Select the point to be al
Page 44 and 45: OTHER FEATURES Turn off X diagram W
Page 46 and 47: SETTINGS These settings are unique
Page 48 and 49: CONFIGURATION Up to 15 x 10 points
Page 50 and 51: Change configuration Distances can
Page 52 and 53: One reference point - Levelling To
Page 54 and 55: Measurement point registration Plac
Page 56 and 57: Note A note with up to 20 character
Page 58 and 59: function is enabled, it will contin
Page 60 and 61: Measurement values for each point c
Page 62 and 63: Evaluating the result The result is
Page 64 and 65: The actual Y value for the selected
Page 68 and 69: SETTINGS The settings are unique fo
Page 70 and 71: Exit Exits the Settings and returns
Page 72 and 73:
Enter diameters and number of point
Page 74 and 75:
COARSE ADJUSTMENT Three reference p
Page 76 and 77:
MEASUREMENT Summary screen The summ
Page 78 and 79:
The colour indicates the status of
Page 80 and 81:
REFERENCES There are different ways
Page 82 and 83:
MEASUREMENT RESULT Summary screen S
Page 84 and 85:
List screen The list screen shows a
Page 86 and 87:
ALIGNMENT Select the point to be al
Page 88 and 89:
FLANGE MEASUREMENT Flange measureme
Page 90 and 91:
Fixturlaser XA Geometry Manual 6.24
Page 92 and 93:
STRAIGHTNESS MEASUREMENT The screen
Page 94 and 95:
CIRCULAR FLATNESS MEASUREMENT The s
Page 96 and 97:
MOUNTING Mounting to magnetic base
Page 98 and 99:
Placing of the magnetic base for bo
Page 100 and 101:
MOUNTING Mounting to magnetic base
Page 102 and 103:
Page 104 and 105:
MOUNTING See T110. Fixturlaser XA G
Page 106 and 107:
MOUNTING Straightness The T21 is mo
Page 108 and 109:
10. Adjust to the R value using the
Page 110 and 111:
1. Turret with built-in angular pri
Page 112 and 113:
MOUNTING Straightness The T220 can
Page 114 and 115:
8. Adjust to the R value using the
Page 116 and 117:
The receiver together with the lase
Page 118 and 119:
Page 120 and 121:
Ambient light protection Optical fi
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Operating time 15 hours Fixturlaser
Page 128 and 129:
Page 130 and 131:
Power supply 4 batteries type LR6 (
Page 132 and 133:
The built-in angular prism works as
Page 134:
show all

user´s manual fixturlaser xa geometry

Create successful ePaper yourself

Delete template?

Save as template?