ERF298MSW - Free-Instruction-Manuals.com

More documents

Recommendations

Info

Fig 1 Fig 2 Fig 3 Fig 4 1 2. INSTALLING OR REMOVING A BLADE Warning: Only use genuine Erbauer blades which are designed for this machine. Ensure that the maximum speed of the blade is compatible with the machine. Note: It is recommended that the operator considers wearing protective gloves when handling the blade during installation or when changing the machines blade. 1. Ensure the cutting head is up and the battery is removed from the machine. See section (Installing/ removing the Battery Pack) below. 2. Press the lower guard lock lever and rotate the lower guard upwards to access the blade cover plate. 3 Release the cover plate from the machine by removing the cross-headed screw securing the black cover plate to the top guard (Fig 1). Store this screw safely for future use. 4. The front locating screw is a fixed shoulder screw and should not be touched. Slide and rotate the cover plate to expose the blade arbor nut. (Fig 2) 5. Locate the pins of the ‘C’ spanner into the holes in the outer blade flange, and hold the spanner firmly to prevent the arbor from rotating. (Fig. 3) 6. Using the supplied Hex-headed spanner release the arbor screw to remove the blade. (Fig. 4) Note: The arbor screw has a left hand thread. ERBAUER 24V 165MM SINGLE BEVEL MITRE SAW
7. Install the new 165 mm (6.5”) blade. Make sure the rotation arrow on the blade matches the clockwise rotation arrow on the upper guard. The blade teeth should always point downward at the front of the saw. (Fig 5) 8. Re-install the outer blade flange ensuring that it is seated correctly on the arbor. 9. Refit and hand-tighten the arbor screw. 10. Prevent arbor rotation by using the ‘C’ spanner as in point 5 above 11. Tighten the arbor screw using moderate force, but do not overtighten. 12. Rotate the cover plate back to its original position, ensuring that the lower blade guard completely covers the blade. 13. Ensure that the lower blade guard operating cog has engaged with the geared quadrant operating lever. (Fig 6) 14. Replace the cross-headed screw and tighten to secure the cover plate into its operational position. 15. Ensure that both blade changing spanners are removed and safely stored for future use. 16. Check the operation of the guard mechanism. Warning: Ensure the blade guard is fully functional before using the machine. Note: Spacers and spindle rings should not be used with this machine and/or blade Fig 5 Fig 6 ERBAUER 24V 165MM SINGLE BEVEL MITRE SAW
Page 1 and 2: Original Instructions Read instruct
Page 3 and 4: Congratulations on your purchase of
Page 5 and 6: 12 Secure work - Where possible use
Page 7 and 8: a. Maintain a firm grip with both h
Page 9 and 10: 20. The operator is adequately trai
Page 11 and 12: 10. Keep the power cord and the cha
Page 13 and 14: SPECIFIC SAFETY RULES & SYMBOLS WAR
Page 15 and 16: Fig 2 15 9. DUST BAG OUTLET 10. TAB
Page 17: ACCESORIES 1x instruction manual 1x
Page 21 and 22: 4. Firmly slide the battery pack do
Page 23 and 24: OPERATING INSTRUCTIONS Caution: The
Page 25 and 26: 4. THE TRIGGER SWITCH The on/off tr
Page 27 and 28: 8. MITRE CUTTING An angle of up to
Page 29 and 30: 13. CUTTING BOWED MATERIAL Before c
Page 31 and 32: The 45 0 bevel setting can also be
Page 33 and 34: etailer for recycling advice. PLUG

ERF298MSW - Free-Instruction-Manuals.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?