ERF298MSW - Free-Instruction-Manuals.com

More documents

Recommendations

Info

Fig 14 d) Press the lower guard release lever to release the saw head. e) Gently push the saw head down and cut through the workpiece. f) After the cut is completed, turn off the saw using the trigger switch, and allow the blade to come to a complete halt. 7. SLIDE CUTTING Caution: NEVER pull the saw towards you when making a cut. The blade can suddenly climb up on top of the workpiece and force itself toward you. This saw is equipped with a sliding carriage system. Loosening the slide lock knob will release the slide (Fig 14) and allow the cutting head to move forwards and backwards. During slide cutting the saw blade is lowered into the workpiece and then pushed to the rear of the saw to complete the cut. This type of cut can be used for cutting wide pieces. 1. Put the workpiece against fence and secure with clamps as appropriate. 2. Loosen the slide lock knob. 3. Grasp the saw handle and pull the cutting head until the arbor (centre of saw blade) is over the front edge of the workpiece. 4. Press the lower blade guard locking trigger for cutting head release. 5. Switch on the saw and allow the saw to reach full speed. 6. Push the saw handle all the way down and cut through the leading edge of the workpiece. 7. Gently push the saw handle towards the fence completing the cut. 8. Push the cutting head to the full rear position after each cut. 9. Release the trigger to switch off the saw. Allow the blade to come to a complete halt before moving hands or removing the workpiece. ERBAUER 24V 165MM SINGLE BEVEL MITRE SAW
8. MITRE CUTTING An angle of up to 45 0 to the left or right can be obtained and a protractor scale can be found on the front of the machine table. Positive stops are provided at 15 0 , 22.5 0 , 30 0 and 45 0 right and left. 1. Loosen the slide locking knob and push the cutting head back as far as it will go and lock the slide. 2. Loosen the mitre angle lock knob. (Fig 15 a) 3. Push down the positive stop locking lever. (Fig 15 b) 4. Turn the rotary table to the desired angle as indicated by the mitre angle pointer. 5. Tighten the mitre angle lock knob to hold the desired angle. 6. If necessary unlock the cutting head by loosening the slide locking knob. This will allow the cutting head to move backwards and forwards (required when cutting wide boards). 7. Start the saw and allow it to reach full speed before commencing operations. 9. BEVEL CUTTING The cutting head can be tilted up to 45 0 to the left hand side only. A large Bevel Lock hand wheel can be found at the rear of the machine, and a 0-45 0 protractor scale is positioned on the slide carriage casting to the front of the hand wheel. (Fig 16) 1. Lock the cutting head down with the head latching pin. 2. Loosen the bevel lock hand wheel. 3. Tilt the cutting head to the required angle. A protractor scale and pointer is provided to aid setting. 4. Tighten the bevel lock hand wheel securely when the desired angle is achieved. 5. Unlatch the cutting head. 6. Release the slide (if necessary) to cut wide workpieces. 7. Stand to the left side of the handle to make the cut. 8. When the cut is completed, release the trigger switch and allow the saw blade to come to a complete halt, before removing the workpiece or your hands from the saw. Fig 15 Fig 16 ERBAUER 24V 165MM SINGLE BEVEL MITRE SAW 15B 1
Page 1 and 2: Original Instructions Read instruct
Page 3 and 4: Congratulations on your purchase of
Page 5 and 6: 12 Secure work - Where possible use
Page 7 and 8: a. Maintain a firm grip with both h
Page 9 and 10: 20. The operator is adequately trai
Page 11 and 12: 10. Keep the power cord and the cha
Page 13 and 14: SPECIFIC SAFETY RULES & SYMBOLS WAR
Page 15 and 16: Fig 2 15 9. DUST BAG OUTLET 10. TAB
Page 17 and 18: ACCESORIES 1x instruction manual 1x
Page 19 and 20: 7. Install the new 165 mm (6.5”)
Page 21 and 22: 4. Firmly slide the battery pack do
Page 23 and 24: OPERATING INSTRUCTIONS Caution: The
Page 25: 4. THE TRIGGER SWITCH The on/off tr
Page 29 and 30: 13. CUTTING BOWED MATERIAL Before c
Page 31 and 32: The 45 0 bevel setting can also be
Page 33 and 34: etailer for recycling advice. PLUG

ERF298MSW - Free-Instruction-Manuals.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?