ERF298MSW - Free-Instruction-Manuals.com

More documents

Recommendations

Info

Fig 25 Four laser module mounting/adjustment screws are provided. Two hex socket grub screws are positioned on the LH side of the laser housing (Fig 25), and one on the RH side of the laser housing. A final cross-headed fixing screw is to be found just below the laser lens. These screws gently hold the laser module in place and on alignment by bearing on the laser modules casing. It is important that during any adjustment the pressure on the laser module casing is maintained as closely as possible to the factory setting. Do not over tighten any one screw – damage to the laser casing could result. B) Adjusting the Angle of the Laser Guide 1) Loosen the cross-headed screw. 2) Loosen the single screw on the RH side of the laser housing ¼ a turn. 3) Turn the laser element in the desired direction to adjust the laser angle. 4) Retighten the adjustment screws. C) Aligning the Laser Beam 1. Loosen the cross-headed screw. 1) Loosen the right hand screw ¼ of a turn. 2) Use the two adjusting screws on the LH side of the laser housing. 3) Adjust both screws until laser alignment is achieved. 4) Retighten right hand screw. 5) Retighten the cross-headed screw Note: Use only the correct sized hex key when adjusting the grub screws. Turn one screw at a time and only ¼ turn in either direction before checking laser alignment. Maintain as far as possible the original factory pressure setting that these screws exert on the laser module LUBRICATION & CLEANING Note Any maintenance must be carried out with the machine switched off and disconnected from the mains power supply. All motor bearings in this machine are lubricated for life. No further lubrication is required. ERBAUER 24V 165MM SINGLE BEVEL MITRE SAW
etailer for recycling advice. PLUG REPLACEMENT Apply light machine oil to the machines pivot points and lower blade The fuse operating in the main arm. plug Avoid of your excessive power oil, toolto which sawdust should will always cling. be replaced with one of identical rating. Periodically, sawdust may accumulate under the work table and the Check base. the Use voltage a vacuum given on cleaner your power to remove tool matches the supply voltage. this sawdust. Use a clean, The slightly power damp tool is cloth supplied to clean with a the fi tted plastic plug, parts of the however machine. if you Do not should use need solvents to fi t a or new similar plug products which follows could the instruction damage the below. plastic parts. WARNING: Do IMPORTANT not attempt to clean by inserting pointed objects through The openings wire in the in mains the machines lead are casings coloured etc. in The machines air accordance vents should with be the cleaned following using code: <strong>com</strong>pressed dry air. Blue ---Neutral Brown ---Live PLUG REPLACEMENT The wire that is coloured blue must be connected to the terminal that is marked with The fuse in the the main letter plug N. of The your wire power that is tool coloured should always brown must be connected to the terminal that is be replaced with one of identical rating. marked with the letter L. A 13AMP (BS1363 Check the voltage given on your power tool matches the or BS1363/A) plug must be used and a 5 AMP supply voltage. fuse must be fi tted. The power tool is supplied with a fitted plug, however if you should need to A 13AMP fit a new (BS1363 plug follows or BS1363/A) the instruction plug below. must be IMPORTANT used and a 5 AMP fuse must be fi tted. The wire in the mains lead are coloured in accordance with the following code: Blue ---Neutral Brown ---Live 5 AMP FUSE BLUE N (NEUTRAL) BROWN L (LIVE) OUTER SLEEVE The wire that is coloured blue must be connected to the terminal that is marked with the letter N. The wire that is coloured brown must be connected to the terminal that is marked with the letter L. A 13AMP (BS1363 or BS1363/A) plug must be 30used and a 5 AMP fuse must be fitted. A 13AMP (BS1363 or BS1363/A) plug must be used and a 5 AMP fuse must be fitted. ERBAUER 216MM (8”) SLIDING MITRE SA ENVIRONMENTAL PROTECTION CABLE GRIP Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. ERBAUER 24V 165MM SINGLE BEVEL MITRE SAW
Page 1 and 2: Original Instructions Read instruct
Page 3 and 4: Congratulations on your purchase of
Page 5 and 6: 12 Secure work - Where possible use
Page 7 and 8: a. Maintain a firm grip with both h
Page 9 and 10: 20. The operator is adequately trai
Page 11 and 12: 10. Keep the power cord and the cha
Page 13 and 14: SPECIFIC SAFETY RULES & SYMBOLS WAR
Page 15 and 16: Fig 2 15 9. DUST BAG OUTLET 10. TAB
Page 17 and 18: ACCESORIES 1x instruction manual 1x
Page 19 and 20: 7. Install the new 165 mm (6.5”)
Page 21 and 22: 4. Firmly slide the battery pack do
Page 23 and 24: OPERATING INSTRUCTIONS Caution: The
Page 25 and 26: 4. THE TRIGGER SWITCH The on/off tr
Page 27 and 28: 8. MITRE CUTTING An angle of up to
Page 29 and 30: 13. CUTTING BOWED MATERIAL Before c
Page 31: The 45 0 bevel setting can also be

ERF298MSW - Free-Instruction-Manuals.com

Create successful ePaper yourself

Delete template?

Save as template?