Liebert® Series 610™ UPS - Jonweb.net

More documents

Recommendations

Info

History Status Operation The History Status screen displays 64 frames, of 4 milliseconds each, from the Present Status screen. Note that the values for output volts and amps are updated once each millisecond. Alarms are listed in the sequence they occurred, within 1 millisecond resolution. The frames are stored in a buffer (a computer information storage technique). The buffer stores the frames in a first in, first out sequence. As a new frame enters the buffer the oldest one is released. When a designated fault occurs (see list below), the buffer stores information for the next 24 frames and then freezes (stops gathering information). At that time, the History Status screen contains 40 frames before the fault, the frame when the fault occurred and 23 frames after the fault. This 64-page report is a very useful diagnostic tool for the operator or Liebert Global Services. Use the Up and Down pads to view the screens. Figure 25 History status report screens HISTORY STATUS MODULE-0 04/10/97 16:49:21 FRAME 36 ORDER - 000000 SITE ID - 00000 SITE TAG - 0000000 **** ACTIVE ALARMS **** Output Ov-volts OUTPUT VOLTS OUTPUT AMPS OUTPUT FREQUENCY LOAD KVA BYPASS VOLTS A 480 420 480 B 480 420 480 C 480 420 480 DC LOAD 349 HERTZ 60.0 TIME UP : NEXT FRAME DOWN : PREVIOUS FRAME SELECT : EXIT HISTORY STATUS MODULE-0 04/10/97 01/17/98 16:49:21 11:21:59 FRAME36100 ORDER - 000000 SITE ID - 00000 SITE TAG - 0000000 **** ACTIVE ALARMS **** Batt Output Discharging Ov-volts Low Batt Warning OUTPUT VOLTS OUTPUT AMPS OUTPUT FREQUENCY LOAD OUTPUT KVAVOLTS BYPASS OUTPUTVOLTS AMPS BATTERY VOLTS OUTPUT VOLTS OUPUT AMPS BATTERY AMPS INPUT VOLTS INPUT AMPS OUPUT VOLTS OUTPUT AMPS LOAD KVA A 380 480 530 325 480 380 325 480 325 0 0 480 325 B 480 380 325 530 480 325 380 480 325 0 0 480 325 C 480 380 325 530 480 325 380 480 325 0 0 480 325 DC 390 -645 LOAD HERTZ 60.0 50.0 TIME 349 0:01 UP : NEXT FRAME DOWN : PREVIOUS FRAME 270 SELECT : EXIT 40
Table 5 shows the alarm conditions that stop the History Status buffer from gathering data. Table 5 Alarm conditions that freeze history data gathering Alarm in SCC Auto Transfer to Bypass Output Overvoltage Output undervoltage Overload Transfer Alarm in Module DC Cap Fuse Blown DC Overvoltage Shutdown Inverter Fault Low Battery Shutdown Overload Shutdown Overtemperature Timeout Rectifier Fuse Blown Reverse Power Operation NOTE The Emergency Off alarm will also freeze the SCC History Status buffer with the Auto Transfer to Bypass alarm (if the load is on the <strong>UPS</strong> system when the alarm condition occurs). The History Status buffer does not resume collecting new frames until the fault is cleared and the Alarm Reset pad is pressed for more than 5 seconds (or until the screen clears). 41
Page 1 and 2: AC Power For Business-Critical Cont
Page 3 and 4: TABLE OF CONTENTS BATTERY CABINET P
Page 5 and 6: FIGURES Figure 1 Multi-Module UPS,
Page 7 and 8: IMPORTANT SAFETY INSTRUCTIONS SAVE
Page 9 and 10: Introduction In the unlikely event
Page 11 and 12: Other Factors to Consider Introduct
Page 13 and 14: Introduction Figure 4 SCC controls
Page 15 and 16: Introduction 2. Battery Racks or Ca
Page 17 and 18: Theory of Operation Figure 6 UPS mo
Page 19 and 20: 2.2.2 Rectifier/Charger Theory of O
Page 21 and 22: 2.2.4 Inverter Theory of Operation
Page 23 and 24: Static Switch Isolation Theory of O
Page 25 and 26: Theory of Operation 6. Retransfer I
Page 27 and 28: Operation Figure 8 Typical operator
Page 29 and 30: Operation Figure 10 Liebert Series
Page 31 and 32: 3.2 Menu Tree Navigation Operation
Page 33 and 34: Operation From any primary screen (
Page 35 and 36: Status/Alarm Message Areas Operatio
Page 37 and 38: Alarm Messages Operation The alarm
Page 39 and 40: Operation Figure 17 Monitor/Mimic d
Page 43 and 44: 3.2.4 Walk-In Display Screen Operat
Page 45: Operation Figure 23 Present status
Page 49 and 50: Operation The Summary screen (Figur
Page 51 and 52: Date Operation This is the system
Page 53 and 54: Operation Auto Dial This is a featu
Page 55 and 56: To change the Maximum Auto-Retransf
Page 59 and 60: Operation Battery Rating (Modules O
Page 61 and 62: 3.2.9 Start-Up Procedures Screen Op
Page 63 and 64: Operation Figure 44 SCC shutdown pr
Page 65 and 66: Operation Values for Calculated Tot
Page 67 and 68: 3.2.12 Meter Calibration Screen Go
Page 69 and 70: 3.2.14 Alarm and Status Messages Op
Page 71 and 72: Table 9 Alarm messages - meaning an
Page 73 and 74: Table 9 Alarm messages - meaning an
Page 75 and 76: Operation Table 10 Alarm messages -
Page 77 and 78: Operation For example, to see a cop
Page 79 and 80: 3.3 Modes of Operation Operation Th
Page 81 and 82: Operation Figure 53 Load on bypass,
Page 83 and 84: Operation 3.3.4 Input Power Failure
Page 85 and 86: Operation 3.3.6 Off Battery The bat
Page 87 and 88: Operation 3.3.8 Remote Emergency Po
Page 89 and 90: Operation . ! CAUTION Instructions
Page 91 and 92: Operation Step 1. Before you apply
Page 93 and 94: Operation e. If the UPS Bypass line
Page 95 and 96: Operation Figure 65 Module start-up
Page 97 and 98:
3.4.3 Load Transfer Procedures Oper
Page 99 and 100:
3.4.5 Shutdown Procedures Operation
Page 101 and 102:
Local Emergency Modules Off (LEMO)
Page 103 and 104:
Operation 3.5.3 Automatic Retransfe
Page 105 and 106:
4.2 Liebert Global Services Start-u
Page 107 and 108:
4.3.3 Limited Life Components Maint
Page 109 and 110:
Battery Safety Precautions In Frenc
Page 111 and 112:
Table 13 Battery Manufacturer Dynas
Page 113 and 114:
4.6 Reporting a Problem Maintenance
Page 115 and 116:
5.2 Environmental Conditions Table
Page 117 and 118:
5.5 Electrical Specifications Speci
Page 120:
Ensuring The High Availability Of M
show all

Liebert® Series 610™ UPS - Jonweb.net

Create successful ePaper yourself

Delete template?

Save as template?