SIGNALTEK Users Guide V1.0 English - Ideal Industries

More documents

Recommendations

Info

Updating Firmware The Firmware Version screen displays SIGNALTEK’s current firmware. The firmware can up updated by downloading a new file from IDEAL’s website: www.idealindustries.com. Figure 2-19 Firmware Version To install a new version of firmware: ? Download the new file and save a copy of it onto a USB memory drive. ? Connect the Display and Remote handsets together with an RJ45 patch cord. If necessary, the display handset will update the firmware on the remote handset via the RJ45 port. ? With SIGNALTEK powered off, insert the drive into the USB port. ? Turn on SIGNALTEK and watch for the message that indicates a firmware update is in progress. ? When SIGNALTEK shuts off the update is complete and the USB memory drive can be safely removed. Note: The firmware update file is not deleted from the USB drive after the update process. If SIGNALTEK is rebooted with the USB drive in place it will re-update the tester. To prevent this, 2-14
delete the file from the USB drive after updating the tester. However, if you are updating several SIGNALTEK testers, you can simply take use the same USB drive to update all the testers then delete the file when finished. Note: Do not remove the USB drive while an update is in progress. Doing so may corrupt the on-board Flash memory, which will require factory service. Wait until the SIGNALTEK graphical user interface is displayed before disconnecting the drive. SIGNALTEK Operation Manual 2-15
Page 1: SIGNALTEK TM Cable Performance Test
Page 4 and 5: IDEAL INDUSTRIES STANDARD WARRANTY
Page 6 and 7: Table of Contents Table of Contents
Page 8 and 9: Table of Figures Figure 1-1 T-568 A
Page 10 and 11: testing is critical because the cab
Page 12 and 13: ? Web Performance - Performance tes
Page 14 and 15: Cable types that can be tested with
Page 16 and 17: Table 1-2 Cable Test Ability Chart
Page 18 and 19: Table 1-3 Key and LED Functions But
Page 20 and 21: Batteries & Power Each SIGNALTEK ha
Page 22 and 23: Graphical User Interface Navigation
Page 24 and 25: Figure 1-5 AutoTest Tab - Inactive
Page 27 and 28: 2 Setup and Configuration The follo
Page 29 and 30: Autotest Modes SIGNALTEK will perfo
Page 31 and 32: Figure 2-7 Cable Performance Setup
Page 33 and 34: Figure 2-9 IP Address Setup When DH
Page 35 and 36: each cable can be found on the cabl
Page 37 and 38: Measurement Units This function con
Page 39: Language SIGNALTEK can support a va
Page 44 and 45: eport. Therefore, leaving blank fie
Page 46 and 47: Note: If sending the file to anothe
Page 48 and 49: Beginning an Autotest There are thr
Page 50 and 51: Note: The ping test is a low speed
Page 52 and 53: When there is a cable fault (open o
Page 54 and 55: Figure 5-3 Cable Performance Result
Page 56 and 57: excessive attenuation. Increased at
Page 58 and 59: conductor and shield) is present. A
Page 60 and 61: SIGNALTEK’s active LAN features c
Page 62 and 63: Can SIGNALTEK be damaged by pluggin
Page 65 and 66: 7 Care and Calibration Cleaning Cle
Page 67 and 68: 8 Specifications Cable Types Voice/
Page 69 and 70: 9 Customer Service Technical Assist
Page 71 and 72: IDEAL INDUSTRIES (U.K.) Limited 225
Page 73: Manual Part No. 6510-91-0003 Rev. A

SIGNALTEK Users Guide V1.0 English - Ideal Industries

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?